T89C51CC01UA-RLTIM Atmel, T89C51CC01UA-RLTIM Datasheet - Page 15

• Manufacturer Part Number: T89C51CC01UA-RLTIM
• Description: IC 8051 MCU FLASH 32K 44VQFP
• Manufacturer: Atmel
• Series: AT89C CANr

Specifications of T89C51CC01UA-RLTIM

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• For Use With: AT89STK-06 - KIT DEMOBOARD 8051 MCU W/CAN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: T89C51CC01UARLTIM

Example
Reading the Flash or
EEPROM Data
Requests from Host
Answers from
Bootloader
4210E–CAN–03/08
Programming Data (write 55h from 0000h to 0008h in the flash)with SSB in write security
BOOTLOADER
HOST
Programming Data (write 55h from 0000h to 0008h in the flash)
HOST
BOOTLOADER
HOST
BOOTLOADER
HOST
BOOTLOADER
Id_prog_start
Id_error
Id_prog_start
Id_prog_start
Id_prog_data
Id_prog_data
Id_prog_data
Id_prog_data
identifier
identifier
The ID_DISPLAY_DATA flow described below allows the user to read data in the Flash memory
or in the EEPROM data memory. A blank check command on the Flash memory is possible with
this flow.
This operation can be executed only with a device previously opened in communication.
To start the reading operation, the Host sends a “Display Data” CAN message (Id_display_data)
with the area memory selected, the start address and the end address passed in parameter.
The device splits into block of 8 bytes data to transfer to the Host if the number of data to display
is greater than 8 data bytes.
Notes:
The device has two possible answers:
•
•
Answer to a read command:
If the chip is protected from read access an “Error” CAN message is sent (see Section “Error
Message Description”, page 22).
Otherwise:
for a display command the device starts to send the data up to 8 by frame to the host. For a
blank check command, the device sends a result OK or the first address not erased.
1.
2. The Address_start gives the start address to read.
3. The Address_end gives the last address to read.
ID_DISPLAY_DATA
D
- 00h: Display Flash
- 01h: Blank Check on the Flash
- 02h: Display EEPROM data
ata[0] selects the area to read and the operation
Identifier
control
control
ID_DISPLAY_DATA
04
01
08
01
01
01
05
00
Identifier
00 00 00
00
55
02
55
00
00
55
Length
00
data
data
// command_new_data
// command_ok
// error_security
5
55
00
08
55
T89C51CC01 CAN Bootloader
00
Data[0]
00h
01h
02h
55 55 55 55
08
Data[1]
Length
address_start
n
Data[2]
Data[3]
Data[n]
address_end
x
Data[4]
15