ATTINY26-16SC Atmel, ATTINY26-16SC Datasheet - Page 29
![IC AVR MCU 2K 16MHZ COM 20-SOIC](/photos/6/80/68042/453-20-soic_sml.jpg)
ATTINY26-16SC
Manufacturer Part Number
ATTINY26-16SC
Description
IC AVR MCU 2K 16MHZ COM 20-SOIC
Manufacturer
Atmel
Series
AVR® ATtinyr
Specifications of ATTINY26-16SC
Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
USI
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
16
Program Memory Size
2KB (1K x 16)
Program Memory Type
FLASH
Eeprom Size
128 x 8
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 11x10b
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
20-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATTINY26-16SC
Manufacturer:
MITEL
Quantity:
20 000
- Current page: 29 of 182
- Download datasheet (3Mb)
Calibrated Internal
RC Oscillator
Oscillator Calibration
Register – OSCCAL
1477K–AVR–08/10
The calibrated internal RC Oscillator provides a fixed 1.0, 2.0, 4.0, or 8.0 MHz clock. All frequen-
cies are nominal values at 5V and 25°C. This clock may be selected as the system clock by pro-
gramming the CKSEL Fuses as shown in Table 11. If selected, it will operate with no external
components. The CKOPT Fuse should always be unprogrammed when using this clock option.
During Reset, hardware loads the calibration byte into the OSCCAL Register and thereby auto-
matically calibrates the RC Oscillator. At 5V, 25°C and 1.0 MHz Oscillator frequency selected,
this calibration gives a fre-quency within ± 3% of the nominal frequency. Using run-time calibra-
tion methods as described in application notes available at www.atmel.com/avr it is possible to
achieve ± 1% accuracy at any given V
chip clock, the Watchdog Oscillator will still be used for the Watchdog Timer and for the reset
time-out. For more information on the pre-programmed calibration value, see the section “Cali-
bration Byte” on page 109.
Table 11. Internal Calibrated RC Oscillator Operating Modes
Note:
When this oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table 12. PB4 (XTAL1) and PB5 (XTAL2) can be used as general I/O ports.
Table 12. Start-up Times for the Internal Calibrated RC Oscillator Clock Selection
Note:
• Bits 7..0 – CAL7..0: Oscillator Calibration Value
Writing the calibration byte to this address will trim the internal oscillator to remove process vari-
ations from the oscillator frequency. During Reset, the 1 MHz calibration value which is located
in the signature row high byte (address 0x00) is automatically loaded into the OSCCAL Register.
If the internal RC is used at other frequencies, the calibration value must be loaded manually.
This can be done by first reading the signature row by a programmer, and then store the calibra-
tion values in the Flash or EEPROM. Then the value can be read by software and loaded into
the OSCCAl Register. When OSCCAL is zero, the lowest available frequency is chosen. Writing
non-zero values to this register will increase the frequency of the internal oscillator. Writing $FF
to the register gives the highest available frequency. The calibrated Oscillator is used to time
SUT1..0
10
00
01
11
(1)
Bit
$31 ($51)
Read/Write
Initial Value
1. The device is shipped with this option selected.
1. The device is shipped with this option selected.
CKSEL3..0
Start-up Time from
0001
0010
0100
0011
Power-down
(1)
CAL7
R/W
6 CK
6 CK
6 CK
7
CAL6
R/W
6
CAL5
R/W
Additional Delay from
5
Device Specific Calibration Value
Reset (V
CC
and Temperature. When this oscillator is used as the
CAL4
R/W
4.1 ms
65 ms
4
Reserved
CC
–
Nominal Frequency (MHz)
= 5.0V)
CAL3
R/W
3
1.0
2.0
4.0
8.0
CAL2
R/W
2
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
CAL1
R/W
1
CAL0
R/W
0
OSCCAL
29
Related parts for ATTINY26-16SC
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATtiny26](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATTINY26-16MU](/photos/12/13/121313/attiny26-16mu_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ IND 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16SU](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ IND 20-SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16PU](/photos/6/80/68043/313-20-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ IND 20-DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16MI](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ IND 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16PI](/photos/6/80/68043/313-20-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ IND 20-DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16SI](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ IND 20-SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16MJ](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
ID MCU AVR 2K 5V 16MHZ 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16MQ](/photos/30/99/309943/qfn-32_tmb.jpg)
Part Number:
Description:
Microcontrollers (MCU) AVR 2K FLASH 128B EE 128B SRAM ADC
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16MC](/photos/12/13/121302/attiny26-16mc_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ COM 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16PC](/photos/6/80/68043/313-20-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ COM 20-DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16PJ](/photos/6/80/68043/313-20-dip_tmb.jpg)
Part Number:
Description:
ID MCU AVR 2K 5V 16MHZ 20-DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16SJ](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
ID MCU AVR 2K 5V 16MHZ 20-SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16SUR](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K 16MHZ IND 20SOIC
Manufacturer:
Atmel
Datasheet: