AT91RM9200-CI-002 Atmel, AT91RM9200-CI-002 Datasheet - Page 13

• Manufacturer Part Number: AT91RM9200-CI-002
• Description: IC ARM9 MCU 256 BGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91RM9200-CI-002

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: POR
• Number Of I /o: 122
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: ROM
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-BGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Data Converters: -

5. Power Considerations
5.1
5.2
6. I/O Considerations
6.1
6.2
6.3
1768MS–ATARM–09-Jul-09
Power Supplies
Power Consumption
JTAG Port Pins
Test Pin
Reset Pin
The AT91RM9200 has five types of power supply pins:
The double power supplies VDDIOM and VDDIOP are identified in
Table 4-2 on page
facing with memories and for interfacing with peripherals.
Ground pins are common to all power supplies, except VDDPLL and VDDOSC pins. For these
pins, GNDPLL and GNDOSC are provided, respectively.
The AT91RM9200 consumes about 500 µA of static current on VDDCORE at 25⋅ C. For
dynamic power consumption, the AT91RM9200 consumes a maximum of 25 mA on VDDCORE
at maximum speed in typical conditions (1.8V, 25⋅ C), processor running full-performance
algorithm.
TMS and TDI are Schmitt trigger inputs and integrate internal pull-up resistors of 15 kOhm typi-
cal. TCK is a Schmitt trigger input without internal pull-up resistor.
TDO is a tri-state output. The JTAGSEL pin is used to select the JTAG boundary scan when
asserted at a high level. The NTRST pin is used to initialize the EmbeddedICE
The TST0 and TST1 pins are used for manufacturing test purposes when asserted high. As they
do not integrate a pull-down resistor, they must be tied low during normal operations. Driving this
line at a high level leads to unpredictable results.
NRST is a Schmitt trigger without pull-up resistor. The NRST signal is inserted in the Boundary
Scan.
• VDDCORE pins. They power the core, including processor, memories and peripherals;
• VDDIOM pins. They power the External Bus Interface I/O lines; voltage ranges from 3.0V to
• VDDIOP pins. They power the Peripheral I/O lines and the USB transceivers; voltage ranges
• VDDPLL pins. They power the PLL cells; voltage ranges from 1.65V to 1.95V, 1.8V nominal.
• VDDOSC pin. They power both oscillators; voltage ranges from 1.65V to 1.95V, 1.8V
voltage ranges from 1.65V to 1.95V, 1.8V nominal.
3.6V, 3V or 3.3V nominal.
from 3.0V to 3.6V, 3V or 3.3V nominal.
nominal.
11. These supplies enable the user to power the device differently for inter-
Table 4-1 on page 9
AT91RM9200
™
TAP Controller.
and
13