Z8F042AHJ020EC Zilog, Z8F042AHJ020EC Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/7/729/zilog_sml.jpg)
Z8F042AHJ020EC
Manufacturer Part Number
Z8F042AHJ020EC
Description
IC ENCORE XP MCU FLASH 4K 28SSOP
Manufacturer
Zilog
Series
Encore!® XP®r
Specifications of Z8F042AHJ020EC
Core Processor
Z8
Core Size
8-Bit
Speed
20MHz
Connectivity
IrDA, UART/USART
Peripherals
Brown-out Detect/Reset, LED, LVD, POR, PWM, Temp Sensor, WDT
Number Of I /o
23
Program Memory Size
4KB (4K x 8)
Program Memory Type
FLASH
Eeprom Size
128 x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 105°C
Package / Case
28-SSOP
Processor Series
Z8F042xx
Core
eZ8
Data Bus Width
8 bit
Data Ram Size
1 KB
Interface Type
UART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
23
Number Of Timers
16 Bit
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 105 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 8 Channel
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
269-3370
Errata for Z8 Encore! XP
Errata for Date Codes 0439 and later
The errata listed in
0439 and later, where the code is YYWW (year and week of assembly). When reviewing the following
errata, refer to the most recent version of the product specification. Data contained in the document is Pre-
liminary only. Refer to the product specification for the supported memory configurations.
Table 2. Z8 Encore! XP
UP006912-0308
Sl
No. Summary
1
2
3
4
5
Internal Precision
Oscillator (IPO)
frequency out of
specification over
voltage and
temperature.
Low Power Op Amp
(LPO) sink current is
less than specified in
the product
specification.
Temperature
sensor absolute
error exceeds
specification.
Writes to the Timer
Polarity (TPOL) bit
must be done twice
when the timer is not
enabled.
Programmable
pull-up resistors
source less than the
specified current.
Later
Table 2
®
are found in the Z8 Encore! XP
Description
The IPO frequency is specified to be 5.5296 MHz +/- 4% over the supply
voltage range of 2.7 V to 3.6 V and the temperature range of -40 °C to +105
°C. Actual silicon performance is +/-4% only over a supply voltage range of
3.15 V to 3.45 V and a temperature range of 0 °C to +70 °C.
Workaround
If the application requires better than +/-4% oscillator accuracy, the voltage
and temperature must be controlled such that they remain within the ranges
given above.
The sink current may drop below 1 µA over temperature and supply voltage.
Workaround
An external pull-down resistor will improve the sink current performance.
The temperature sensor absolute error is outside the specification over the full
temperature/voltage range.
Workaround
Recalibrate the sensor at the user application temperature or use the temper-
ature sensor output for relative measurements.
When the timer is not enabled, the TPOL bit does not affect the timer output
when changed.
Workaround
When the timer is not enabled, write the Timer Control Register 1 twice with
the same value. This will cause the correct timer output behavior to occur.
The pull-up devices are specified to source at least 30 µA. In actuality, the pull-
up devices may source as little as 7 µA.
Workaround
If a faster pull-up is required, use an external pull-up resistor.
F082A Series Errata (8-pin Devices) with Date Codes 0439 and
®
F082A Series (8-pin devices)
®
Errata for Z8 Encore! XP
F082A Series 8-pin products with date codes
®
F082A Series
Page 2 of 14