MCHC908RF2CFAE Freescale Semiconductor, MCHC908RF2CFAE Datasheet - Page 77

• Manufacturer Part Number: MCHC908RF2CFAE
• Description: IC MCU W/UHF TX 2K FLASH 32LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCHC908RF2CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 4MHz
• Peripherals: LVD, POR, PWM, RF Mod
• Number Of I /o: 12
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Connectivity: -

6.4.2 Enabling the Clock Monitor
MC68HC908RF2 — Rev. 4.0
MOTOROLA
start
loop
start
loop
lda
**
sta
cmpa
bne
lda
**
sta
brset
cmpa
bne
#$13
**
icgcr
icgcr
loop
#$AF
**
icgcr
6,ICGCR,error ;Verify CMF is not set
icgcr
loop
Figure 6-8. Code Example for Enabling the Clock Monitor
Many applications require the clock monitor to determine if one of the clock sources
has become inactive, so the other can be used to recover from a potentially
dangerous situation. Using the clock monitor requires both clocks to be active
(ECGON and ICGON both set). To enable the clock monitor, both clocks also must
be stable (ECGS and ICGS both set). This is to prevent the use of the clock monitor
when a clock is first turned on and potentially unstable.
Enabling the clock monitor and clock monitor interrupts requires a flow similar to
this flow:
These events must happen in sequence. A short assembly code example of how
to employ this flow is shown in
and does not represent valid syntax for any particular assembler.
Figure 6-7. Code Example for Switching Clock Sources
1. Enable the alternate clock source
2. Wait for both clock sources to be stable
3. Switch to the desired clock source if necessary
4. Enable the clock monitor
5. Enable clock monitor interrupts
Freescale Semiconductor, Inc.
;Clock Switching Code Example
;This code switches from Internal to External clock
;Clock Monitor and interrupts are not enabled
;Mask for CS, ECGON, ECGS
;If switching from External to Internal, mask is $0C.
;Other code here, such as writing the COP, since ECGS may
;take some time to set
;Try to set CS, ECGON and clear ICGON. ICGON will not
;clear until CS is set, and CS will not set until
;ECGON and ECGS are set.
;Check to see if ECGS set, then CS set, then ICGON clear
;Keep looping until ICGON is clear.
For More Information On This Product,
Internal Clock Generator Module (ICG)
;Mask for CMIE, CMON, ICGON, ICGS, ECGON, ECGS
;Other code here, such as writing the COP, since ECGS
;Try to set CMIE. CMIE wont set until CMON set; CMON
;Check if ECGS set, then CMON set, then CMIE set
;Keep looping until CMIE is set.
;Clock Monitor Enabling Code Example
;This code turns on both clocks, selects the desired
; one, then turns on the Clock Monitor and Interrupts
; If Internal Clock desired, mask is $AF
; If External Clock desired, mask is $BF
; If interrupts not desired mask is $2F int; $3F ext
; and ICGS may take some time to set.
; won’t set until ICGON, ICGS, ECGON, ECGS set.
Go to: www.freescale.com
Figure
6-8. This code is for illustrative purposes only
Internal Clock Generator Module (ICG)
Usage Notes
Data Sheet
77