MCP6004-I/P Microchip Technology, MCP6004-I/P Datasheet - Page 11

• Manufacturer Part Number: MCP6004-I/P
• Description: IC OPAMP QUAD 1.8V 14DIP
• Manufacturer: Microchip Technology

Specifications of MCP6004-I/P

• Slew Rate: 0.6 V/µs
• Package / Case: 14-DIP (0.300", 7.62mm)
• Amplifier Type: General Purpose
• Number Of Circuits: 4
• Output Type: Rail-to-Rail
• Gain Bandwidth Product: 1MHz
• Current - Input Bias: 1pA
• Voltage - Input Offset: 4500µV
• Current - Supply: 100µA
• Current - Output / Channel: 23mA
• Voltage - Supply, Single/dual (±): 1.8 V ~ 6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Number Of Channels: 4
• Common Mode Rejection Ratio (min): 60 dB
• Input Offset Voltage: 4.5 mV
• Input Bias Current (max): 19 pA
• Operating Supply Voltage: 3 V, 5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: Through Hole
• Shutdown: No
• Supply Voltage (max): 6 V
• Supply Voltage (min): 1.8 V
• Technology: CMOS
• Voltage Gain Db: 112 dB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

3.0
Descriptions of the pins are listed in
TABLE 3-1:
3.1
The output pins are low-impedance voltage sources.
3.2
The
high-impedance CMOS inputs with low bias currents.
3.3
The positive power supply (V
than the negative power supply (V
operation, the other pins are at voltages between V
and V
Typically, these parts are used in a single (positive)
supply configuration. In this case, V
ground and V
need bypass capacitors.
© 2009 Microchip Technology Inc.
MCP6001 MCP6001R MCP6001U
SOT-23-5
SC70-5,
—
—
—
—
—
—
—
—
—
—
1
4
3
5
2
DD
non-inverting
.
PIN DESCRIPTIONS
Analog Outputs
Analog Inputs
Power Supply Pins
SOT-23-5
DD
is connected to the supply. V
—
—
—
—
—
—
—
—
—
—
PIN FUNCTION TABLE
1
4
3
2
5
and
SOT-23-5
DD
inverting
—
—
—
—
—
—
—
—
—
—
) is 1.8V to 6.0V higher
4
3
1
5
2
SS
Table
SS
is connected to
). For normal
MSOP,
PDIP,
SOIC
inputs
3-1.
MCP6002
—
—
—
—
—
—
—
1
2
3
8
5
6
7
4
DD
are
will
DFN
2x3
SS
—
—
—
—
—
—
1
2
3
8
5
6
7
4
9
MCP6004
TSSOP
SOIC,
PDIP,
10
11
12
13
14
—
1
2
3
4
5
6
7
8
9
3.4
There is an internal electrical connection between the
Exposed Thermal Pad (EP) and the V
be connected to the same potential on the Printed
Circuit Board (PCB).
MCP6001/1R/1U/2/4
V
V
V
OUT
Exposed Thermal Pad (EP)
IN
IN
Symbol
V
V
V
V
V
V
V
V
V
+, V
–, V
V
V
OUTB
OUTC
OUTD
INC
INC
IND
IND
EP
, V
INB
INB
DD
SS
OUTA
INA
INA
+
–
–
+
+
–
– Inverting Input (op amp A)
+ Non-inverting Input (op amp A)
Analog Output (op amp A)
Positive Power Supply
Non-inverting Input (op amp B)
Inverting Input (op amp B)
Analog Output (op amp B)
Analog Output (op amp C)
Inverting Input (op amp C)
Non-inverting Input (op amp C)
Negative Power Supply
Non-inverting Input (op amp D)
Inverting Input (op amp D)
Analog Output (op amp D)
Exposed Thermal Pad (EP);
must be connected to VSS.
Description
DS21733J-page 11
SS
pin; they must