AD623ARZ Analog Devices Inc, AD623ARZ Datasheet - Page 15

• Manufacturer Part Number: AD623ARZ
• Description: IC AMP INST R-R LP 8SOIC
• Manufacturer: Analog Devices Inc
• Type: Low Powerr

Specifications of AD623ARZ

• Slew Rate: 0.3 V/µs
• Amplifier Type: Instrumentation
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• -3db Bandwidth: 800kHz
• Current - Input Bias: 17nA
• Voltage - Input Offset: 25µV
• Current - Supply: 375µA
• Voltage - Supply, Single/dual (±): 2.7 V ~ 12 V, ± 2.5 V ~ 6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• No. Of Amplifiers: 1
• Input Offset Voltage: 200µV
• Gain Db Min: 1dB
• Gain Db Max: 1000dB
• Bandwidth: 800kHz
• Amplifier Output: Single Ended
• Cmrr: 110dB
• Supply Voltage Range: 2.7V To
• Common Mode Rejection Ratio: 110
• Current, Input Bias: 17 nA
• Current, Input Offset: 0.25 nA
• Current, Supply: 550 μA
• Impedance, Thermal: 155 °C/W
• Package Type: SOIC-N
• Power Dissipation: 650 mW
• Temperature, Operating, Range: -40 to +85 °C
• Voltage, Gain: 1-1000 V/V
• Voltage, Input: -4.85 to +3.5 V
• Voltage, Input Offset: 25 μV
• Voltage, Noise: 35 nV/sqrt Hz (Input), 50 nV/sqrt Hz (Output)
• Voltage, Output Swing: 0.01 to 4.5 V
• Voltage, Supply: 2.7 to 12 V
• Rohs Compliant: Yes
• Number Of Channels: 1
• Number Of Elements: 1
• Power Supply Requirement: Single/Dual
• Input Resistance: 2000@5VMohm
• Input Bias Current: 0.025@5VnA
• Single Supply Voltage (typ): 3/5/9V
• Dual Supply Voltage (typ): ±3/±5V
• Power Supply Rejection Ratio: 80dB
• Rail/rail I/o Type: Rail to Rail Output
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 12V
• Dual Supply Voltage (min): ±2.5V
• Dual Supply Voltage (max): ±6V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output / Channel: -
• Gain Bandwidth Product: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

THEORY OF OPERATION
The AD623 is an instrumentation amplifier based on a modified
classic 3-op-amp approach, to assure single or dual supply
operation even at common-mode voltages at the negative
supply rail. Low voltage offsets, input and output, as well as
absolute gain accuracy, and one external resistor to set the
gain, make the AD623 one of the most versatile instrumentation
amplifiers in its class.
The input signal is applied to PNP transistors acting as voltage
buffers and providing a common-mode signal to the input
amplifiers (see Figure 41). An absolute value 50 kΩ resistor in
each amplifier feedback assures gain programmability.
The differential output is
The differential voltage is then converted to a single-ended
voltage using the output amplifier, which also rejects any
common-mode signal at the output of the input amplifiers.
Because the amplifiers can swing to either supply rail, as well as
have their common-mode range extended to below the negative
supply rail, the range over which the AD623 can operate is further
enhanced (see Figure 20 and Figure 21).
V
O
=
⎛
⎜
⎜
⎝
1
+
100
R
G
kΩ
⎞
⎟
⎟
⎠
V
C
Rev. D | Page 15 of 24
The output voltage at Pin 6 is measured with respect to the
potential at Pin 5. The impedance of the reference pin is 100 kΩ;
therefore, in applications requiring V/I conversion, a small
resistor between Pin 5 and Pin 6 is all that is needed.
Note that the bandwidth of the in-amp decreases as gain is
increased. This occurs because the internal op-amps are the
standard voltage feedback design. At unity gain, the output
amplifier limits the bandwidth.
NONINVERTING
INVERTING
GAIN
1
8
2
3
NEGATIVE SUPPLY
POSITIVE SUPPLY
Figure 41. Simplified Schematic
7
4
7
4
50kΩ
50kΩ
50kΩ
50kΩ
50kΩ
50kΩ
OTUPUT
REF
AD623
6
5