OP97EPZ Analog Devices Inc, OP97EPZ Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
OP97EPZ
Manufacturer Part Number
OP97EPZ
Description
IC OPAMP GP LP PREC 8DIP
Manufacturer
Analog Devices Inc
Specifications of OP97EPZ
Slew Rate
0.2 V/µs
Amplifier Type
General Purpose
Number Of Circuits
1
-3db Bandwidth
900kHz
Current - Input Bias
30pA
Voltage - Input Offset
10µV
Current - Supply
380µA
Voltage - Supply, Single/dual (±)
±2 V ~ 20 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Through Hole
Package / Case
8-DIP (0.300", 7.62mm)
Op Amp Type
Low Power
No. Of Amplifiers
1
Bandwidth
900kHz
Supply Voltage Range
± 2V To ± 20V
Amplifier Case Style
DIP
No. Of Pins
8
Common Mode Rejection Ratio
132
Current, Input Bias
±30 pA
Current, Input Offset
30 pA
Current, Supply
380 μA
Impedance, Thermal
43 °C/W
Package Type
PDIP-8
Resistance, Input
30 Megohms
Temperature, Operating, Range
-40 to +85 °C
Voltage, Gain
2000 V/mV
Voltage, Input
±20 V
Voltage, Noise
17 nV/sqrt Hz
Voltage, Offset
10 μV
Voltage, Output, High
+14 V
Voltage, Output, Low
-14 V
Voltage, Supply
±15 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Output Type
-
Current - Output / Channel
-
Gain Bandwidth Product
-
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
ABSOLUTE MAXIMUM RATINGS
Absolute maximum ratings apply to both DICE and packaged
parts, unless otherwise noted.
Table 3.
Parameter
Supply Voltage
Input Voltage
Differential Input Voltage
Differential Input Current
Output Short-Circuit Duration
Operating Temperature Range
OP97E, OP97F (P, S)
Storage Temperature Range
Junction Temperature Range
Lead Temperature (Soldering, 60 sec)
1
2
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
For supply voltages less than ±20 V, the absolute maximum input voltage is
The inputs of the OP97 are protected by back-to-back diodes. Current-
equal to the supply voltage.
limiting resistors are not used in order to achieve low noise. Differential
input voltages greater than 1 V cause excessive current to flow through the
input protection diodes unless limiting resistance is used.
1
2
2
±20 V
Indefinite
Rating
±20 V
±1 V
±10 mA
−40°C to +85°C
−65°C to +150°C
−65°C to +150°C
300°C
Rev. F | Page 5 of 16
THERMAL RESISTANCE
θ
soldered in a circuit board for surface-mount packages.
Table 4
Package Type
8-Lead PDIP (P Suffix)
8-Lead SOIC (S Suffix)
1
ESD CAUTION
θ
device in socket for PDIP package; θ
printed circuit board for SOIC package.
JA
JA
is specified for the worst-case conditions, that is, a device
is specified for worst-case mounting conditions, that is, θ
.
JA
θ
103
158
is specified for device soldered to
JA
1
θ
43
43
JC
JA
is specified for
Unit
°C/W
°C/W
OP97