LMP7721MA/NOPB National Semiconductor, LMP7721MA/NOPB Datasheet - Page 14

• Manufacturer Part Number: LMP7721MA/NOPB
• Description: IC AMP PREC 3FA BIAS CURR 8SOIC
• Manufacturer: National Semiconductor
• Series: LMP®, PowerWise®r

Specifications of LMP7721MA/NOPB

• Amplifier Type: General Purpose
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Slew Rate: 12.8 V/µs
• Gain Bandwidth Product: 17MHz
• Current - Input Bias: 0.003pA
• Voltage - Input Offset: 26µV
• Current - Supply: 1.3mA
• Current - Output / Channel: 60mA
• Voltage - Supply, Single/dual (±): 1.8 V ~ 5.5 V, ±0.9 V ~ 2.75 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Number Of Channels: 2
• Voltage Gain Db: 120 dB
• Common Mode Rejection Ratio (min): 84 dB
• Input Voltage Range (max): 5.5 V
• Input Voltage Range (min): 1.8 V
• Input Offset Voltage: 0.15 mV at 5 V
• Operating Supply Voltage: 3 V, 5 V
• Supply Current: 1.7 mA at 5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• For Use With: LMP7721MAEVAL - BOARD EVALUATION FOR LMP7721
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Details
• Other names: *LMP7721MA; *LMP7721MA/NOPB; LMP7721MA

www.national.com
FIGURE 4. Error Caused by Amplifier’s Input Bias Current
Figure 5 is an example of the LMP7721 used as a pH sensor
amplifier.
The output voltage from the pH electrode is fed to the signal
conductor of the triax and then sent to the non-inverting input
of the LMP7721. In this application, the inverting input is a low
impedance node and hence is used to drive the LMP7715
FIGURE 5. LMP7721 as pH Electrode Amplifier
and Sensor Source Impedance
20204091
20204092
14
which acts as a guard driver. The output of the guard driver
is connected to the guard of the triax via a 100Ω isolation re-
sistor. Ideally, the inverting and the non-inverting inputs of the
amplifier are kept at the same potential through the operation
of the amplifier. By connecting the signal conductor to the
non-inverting input and letting the inverting input drive the
guard, the signal conductor and the guard are kept at the
same potential which prevents leakage from the signal
source.
LAYOUT AND ASSEMBLY CONSIDERATIONS
In order to capitalize on the LMP7721’s ultra low input bias
current, careful circuit layout and assembly are required.
Guarding techniques are highly recommended to reduce par-
asitic leakage current by isolating the LMP7721’s input from
large voltage gradients across the PC board. A guard is a low
impedance conductor that surrounds an input line and its po-
tential is raised to the input line’s voltage. The input pins
should be fully guarded as shown in Figure 6. The guard
traces should completely encircle the input connections. In
addition, they should be located on both sides of the PCB and
be connected together.
Solder mask should not cover the input and the guard area
including guard traces on either side of the PCB.
Sockets are not recommended as they can be a significant
leakage source. After assembly, a thorough cleaning using
commercial solvent is necessary.
FIGURE 6. Circuit Board Guard Layout
20204093