MCP6051-E/SN Microchip Technology, MCP6051-E/SN Datasheet - Page 17

• Manufacturer Part Number: MCP6051-E/SN
• Description: IC OPAMP R-R 1.8V 30UA 8-SOIC
• Manufacturer: Microchip Technology

Specifications of MCP6051-E/SN

• Slew Rate: 0.15 V/µs
• Package / Case: 8-SOIC (3.9mm Width)
• Amplifier Type: General Purpose
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Gain Bandwidth Product: 385kHz
• Current - Input Bias: 1pA
• Voltage - Input Offset: 150µV
• Current - Supply: 30µA
• Current - Output / Channel: 26mA
• Voltage - Supply, Single/dual (±): 1.8 V ~ 6 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Number Of Channels: 1
• Common Mode Rejection Ratio (min): 72 dB
• Input Offset Voltage: 0.15 mV
• Input Bias Current (max): 100 pA
• Operating Supply Voltage: 3 V, 5 V
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Shutdown: No
• Supply Voltage (max): 6 V
• Supply Voltage (min): 1.8 V
• Technology: CMOS
• Voltage Gain Db: 115 dB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

4.6
In applications where low input bias current is critical,
Printed Circuit Board (PCB) surface leakage effects
need to be considered. Surface leakage is caused by
humidity, dust or other contamination on the board.
Under low humidity conditions, a typical resistance
between nearby traces is 10
cause 5 pA of current to flow; which is greater than the
MCP6051/2/4 family’s bias current at +25°C (±1.0 pA,
typical).
The easiest way to reduce surface leakage is to use a
guard ring around sensitive pins (or traces). The guard
ring is biased at the same voltage as the sensitive pin.
An example of this type of layout is shown in
Figure
FIGURE 4-6:
for Inverting Gain.
1.
2.
© 2009 Microchip Technology Inc.
Non-inverting Gain and Unity-Gain Buffer:
a)
b)
Inverting Gain and Transimpedance Gain
Amplifiers (convert current to voltage, such as
photo detectors):
a)
b)
Guard Ring
4-6.
PCB Surface Leakage
Connect the non-inverting pin (V
input with a wire that does not touch the
PCB surface.
Connect the guard ring to the inverting input
pin (V
common mode input voltage.
Connect the guard ring to the non-inverting
input pin (V
to the same reference voltage as the op
amp (e.g., V
Connect the inverting pin (V
with a wire that does not touch the PCB
surface.
IN
–). This biases the guard ring to the
IN
DD
+). This biases the guard ring
Example Guard Ring Layout
/2 or ground).
V
IN
12
– V
Ω. A 5V difference would
IN
+
IN
–) to the input
V
SS
IN
+) to the
4.7
4.7.1
The MCP6051/2/4 op amps can be used in gyrator
applicaitons. The gyrator is an electric circuit which can
make a capacitive circuit behave inductively.
7
inductance, with an approximately equivalent circuit
below. The two Z
applications. The primary application for a gyrator is to
reduce the size and cost of a system by removing the
need for bulky, heavy and expensive inductors. For
example, RLC bandpass filter characteristics can be
realized with capacitors, resistors and operational
amplifiers without using inductors. Moreover, gyrators
will typically have higher accuracy than real inductors,
due to the lower cost of precision capacitors than
inductors.
.
FIGURE 4-7:
Z
shows an example of a gyrator simulating
Z
IN
Z
IN
IN
L
=
=
Application Circuits
R
R
GYRATOR
L
L
RC
+
j
ω
R
L
R
IN
L
C
MCP6051/2/4
L
have similar values in typical
Gyrator.
R
L
MCP6051
Equivalent Circuit
DS22182A-page 17
Gyrator
Figure 4-
V
OUT