HCPL-7510 Avago Technologies US Inc., HCPL-7510 Datasheet
![OPTOCOUPLER AMP 100KHZ 8-DIP](/photos/31/34/313477/516-8-dip_sml.jpg)
HCPL-7510
Specifications of HCPL-7510
Available stocks
Related parts for HCPL-7510
HCPL-7510 Summary of contents
Page 1
... In a typical implementation, motor current flows through an external resistor and the resulting analog voltage drop is sensed by the HCPL-7510. An output voltage is created on the other side of the HCPL- 7510 optical isolation barrier. This single-ended output voltage is proportional to the motor current. Since ...
Page 2
... HCPL-7510-560E to order product of Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant. Example 2: HCPL-7510 to order product of 300 mil DIP package in tube packaging and non-RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Package Outline Drawings HCPL-7510 Standard DIP Package 9.80 ± ...
Page 3
... HCPL-7510 Gull Wing Surface Mount Option 300 Outline Drawing 9.80 ± 0.25 (0.386 ± 0.010 7510 YYWW 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± 0.013) 2.54 (0.100) BSC Dimensions in millimeters (inches). Tolerances (unless otherwise specified): XX.XX = 0.01 Note: Floating lead protusion is 0.5 mm (20 mils) max. ...
Page 4
Solder Reflow Temperature Profile 300 PREHEATING RATE 3°C + 1°C/–0.5°C/SEC. REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. 200 160°C 150°C 140°C 3°C + 1°C/–0.5°C 100 PREHEATING TIME 150° SEC ROOM TEMPERATURE Note: Use of non-chlorine-activated ...
Page 5
... Regulatory Information The HCPL-7510 has been approved by the following organizations: IEC/EN/DIN EN 60747-5-2 Approved under: IEC 60747-5-2:1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01. IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Description Installation classification per DIN EN 0110-1/1997-04, Table 1 ≤ for rated mains voltage ...
Page 6
Insulation and Safety Related Specifications Parameter Symbol Minimum External Air Gap L(101) (clearance) Minimum External Tracking L(102) (creepage) Minimum Internal Plastic Gap (internal clearance) Tracking Resistance CTI (comparative tracking index) Isolation Group Option 300 - surface mount classification is Class ...
Page 7
Electrical Specifications (DC) Unless otherwise noted, all typicals and figures are at the nominal operation conditions 4 5.0 V and T REF DD1 DD2 Operating Conditions. Parameter Symbol Input Offset Voltage ...
Page 8
Switching Specifications (AC) Over recommended operating conditions unless otherwise specified. Parameter Signal Delay (50 – 10%) IN OUT Signal Delay (50 – 50%) IN OUT Signal Delay (50 – 90%) IN ...
Page 9
V – SUPPLY VOLTAGE – Figure 1. Supply current vs. supply voltage. 12.0 11.0 10.0 9.0 8.0 7.0 6.0 5.0 4.0 -0.3 -0.2 -0 – INPUT ...
Page 10
TYPICAL 1.5 MAXIMUM 1.0 0.5 0 -0.5 -1.0 -1.5 -2.0 -40 - – TEMPERATURE – °C A Figure 7. Input offset change vs. temperature. 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 ...
Page 11
... V OUT REF -40 -20 GND2 Figure 13. Propagation delay vs. temperature. IN OUT 0.1 µ 100.0 1000.0 Figure 15. CMTI test circuit. Tp5010 Tp5050 Tp5090 Trise – TEMPERATURE – °C A 78L05 1 0.1 µF 2 HCPL-7510 3 4 PULSE GEN. – 100 V DD2 8 0.1 µ OUT 6 V REF 5 ...
Page 12
... R4 should be chosen to supply sufficient current from the existing floating supply. The voltage from the current sensing resistor (Rsense) is applied to the input of the HCPL-7510 through an RC anti-aliasing filter (R2 and C2). Although the application circuit is relatively simple, a few recom- mendations should be followed to ensure optimal per- formance ...
Page 13
... HCPL-7510. The bypass capacitors are required because of the high-speed digital nature of the signals inside the HCPL-7510. A 0.01 µF bypass capacitor (C2) is also rec- ommended at the input due to the switched-capacitor nature of the input circuit. The input bypass capacitor ...
Page 14
... Smaller sense resistance decreases power dissipation, while larger sense resistance can improve circuit accuracy by utilizing the full input range of the HCPL-7510. The first step in selecting a sense resistor is determining how much current the resistor will be sensing. The graph ...
Page 15
... The Kelvin connections to the resistor should be brought together under the body of the resistor and then run very close to each other to the input of the HCPL-7510; this minimizes the loop area of the connection and reduces the possibility of stray magnetic fields from interfering with the measured signal ...
Page 16
... C INPUT 100 pF works well.) 2.4: How do I ensure that the HCPL-7510 is not destroyed as a result of short circuit conditions which cause voltage drops across the sense resistor that exceed the ratings of the HCPL-7510’s inputs? Select the sense resistor so that it will have less than 5 V drop when short circuits occur ...
Page 17
For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © ...