OP37EZ Analog Devices Inc, OP37EZ Datasheet
OP37EZ
Specifications of OP37EZ
Available stocks
Related parts for OP37EZ
OP37EZ Summary of contents
Page 1
FEATURES Low Noise p-p (0 Hz) 3 nV/÷ kHz Low Drift, 0 High Speed Slew Rate 63 MHz Gain Bandwidth Low Input Offset Voltage Excellent ...
Page 2
... April 2002. Unit ∞C/W ∞C/W ∞C/W is specified for device JA is specified for device JA –2– ORDERING GUIDE Operating CerDIP Plastic Temperature 8-Lead 8-Lead Range OP37AZ* MIL OP37EZ OP37EP IND/COM OP37FP* IND/COM OP37GP XIND OP37GZ OP37GS XIND WARNING! ESD SENSITIVE DEVICE REV. B ...
Page 3
SPECIFICATIONS ( Parameter Symbol Conditions Input Offset Voltage V Note 1 OS Long-Term Stability V /Time Notes Input Offset Current I OS Input Bias Current I B Input Noise Voltage ...
Page 4
... CM = ± 4 ≥ ± 600 1200 O ≥ ± 11.5 ± 13 –25 C < T < +85 C for OP37EZ/FZ < < +85 C for OP37GP/GS/GZ, unless otherwise noted.) OP37E Min Typ Max Min 20 50 0.2 0 ± 14 ± 60 ± 10.5 ± 11.8 ± 10.5 ± 11.8 ...
Page 5
Wafer Test Limits unless otherwise noted.) Parameter Symbol Conditions Input Offset Voltage V Note 1 OS Input Offset Current I OS Input Bias Current I B Input Voltage Range IVR Common Mode = ± ...
Page 6
OP37 Typical Electrical Characteristics Parameter Symbol Conditions Average Input Offset Voltage Drift TCV or Nulled or OS TCV Unnulled OSN Average Input Offset Current Drift TCI OS Average Input Bias Current Drift ...
Page 7
TEST TIME OF 10sec MUST BE USED TO LIMIT LOW FREQUENCY 40 (<0.1Hz) GAIN. 30 0.01 0 100 FREQUENCY – Hz TPC 1. Noise-Tester Frequency Response (0 Hz) 10 ...
Page 8
OP37 60 OP37C 50 OP37B 40 30 OP37A 20 10 OP37B OP37A 0 –10 OP37A –20 –30 OP37B –40 TRIMMING WITH 10k POT DOES –50 NOT CHANGE –60 TCV OS OP37C –70 –75 –50 – 100 ...
Page 9
2 1 1.0 0 TOTAL SUPPLY VOLTAGE – Volts TPC 19. Open-Loop Voltage Gain vs. Supply Voltage 80 60 ...
Page 10
OP37 0.1 F 100k OP37 10 D.U.T. 2k VOLTAGE GAIN 22 F 4.3k = 50,000 OP12 SCOPE 4 100k 110k 2.2 F 0.1 F 24.3k TPC 28. Noise Test Circuit (0 Hz) ...
Page 11
APPLICATIONS INFORMATION OP37 Series units may be inserted directly into 725 and OP07 sockets with or without removal of external compensation or nulling components. Additionally, the OP37 may be fitted to unnulled 741type sockets; however, if conventional 741 nulling circuitry ...
Page 12
OP37 140 120 100 100 , S 1k UNBALANCED 100 1k 10k FREQUENCY – Hz Figure 4b. CMRR vs. Frequency Comments on Noise The OP37 is a very low-noise monolithic ...
Page 13
Table I. Source Device Impedance Comments <500 W Straln Gauge Typically used in low-frequency applications. <1500 W Magnetic Low I B Tapehead set-magnetization problems when direct coupling is used. OP37 I can be neglected. B <1500 W Magnetic Similar need ...
Page 14
OP37 OP37 are free of bias-current transients upon power up or power down. However always advantageous to control the speed of power supply rise and fall, to eliminate transients. In addition, the dc resistance of the head should ...
Page 15
Ceramic DIP – Glass Hermetic Seal [CERDIP] CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 8-Lead Plastic Dual-in-Line Package [PDIP] (N-8) Dimensions shown ...
Page 16
OP37 Revision History Location 12/02–Data Sheet changed from REV REV. B. Edits to BINDING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . ...