LMC6482AIN/NOPB National Semiconductor, LMC6482AIN/NOPB Datasheet - Page 5

• Manufacturer Part Number: LMC6482AIN/NOPB
• Description: IC OP AMP DUAL CMOS R-R 8-DIP
• Manufacturer: National Semiconductor

Specifications of LMC6482AIN/NOPB

• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Output Type: Rail-to-Rail
• Slew Rate: 1.3 V/µs
• Gain Bandwidth Product: 1.5MHz
• Current - Input Bias: 0.02pA
• Voltage - Input Offset: 110µV
• Current - Supply: 1.3mA
• Current - Output / Channel: 30mA
• Voltage - Supply, Single/dual (±): 3 V ~ 15.5 V, ±1.5 V ~ 7.75 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Bandwidth: 1.5 MHz
• Channel Separation: 150
• Common Mode Rejection Ratio: 82
• Current, Input Bias: 0.02 pA
• Current, Input Offset: 0.01 pA
• Current, Output: 30 mA
• Current, Supply: 1.3 mA
• Harmonic Distortion: 0.01 %
• Impedance, Thermal: 90 °C/W
• Number Of Amplifiers: Dual
• Package Type: MDIP-8
• Resistance, Input: 10 Teraohms
• Temperature, Operating, Range: -40 to +85 °C
• Voltage, Gain: 666 V/mV
• Voltage, Input: 3 to 15.5 V
• Voltage, Noise: 37 nV/sqrt Hz
• Voltage, Offset: 0.11 mV
• Voltage, Output, High: 14.7 V
• Voltage, Output, Low: 0.16 V
• Voltage, Supply: 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device
• Other names: *LMC6482AIN; *LMC6482AIN/NOPB; LMC6482AIN

AC Electrical Characteristics
Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the
maximum allowed junction temperature of 150˚C. Output currents in excess of
Note 4: The maximum power dissipation is a function of T
− T
Note 5: Typical Values represent the most likely parametric norm.
Note 6: All limits are guaranteed by testing or statistical analysis.
Note 7: V
Note 8: Do not short circuit output to V
Note 9: V
Note 10: Input referred, V
Note 11: Connected as voltage Follower with 2V step input. Number specified is the slower of either the positive or negative slew rates.
Note 12: Limiting input pin current is only necessary for input voltages that exceed absolute maximum input voltage ratings.
Note 13: Guaranteed limits are dictated by tester limitations and not device performance. Actual performance is reflected in the typical value.
Note 14: For guaranteed Military Temperature parameters see RETS6482X.
Typical Performance Characteristics
specified
V
A
S
)/θ
= +15V, Single Supply, T
JA
. All numbers apply for packages soldered directly into a PC board.
+
+
= 15V, V
= 15V. Connected as Voltage Follower with 10V step input. Number specified is the slower of either the positive or negative slew rates.
Sourcing Current vs. Output Voltage
Supply Current vs. Supply Voltage
CM
= 7.5V and R
+
= 15V and R
L
A
connected to 7.5V. For Sourcing tests, 7.5V ≤ V
+
= 25˚C unless otherwise
, when V
L
= 100 kΩ connected to 7.5V. Each amp excited in turn with 1 kHz to produce V
+
is greater than 13V or reliability will be adversely affected.
J(max)
01171340
01171342
, θ
(Continued)
JA
, and T
A
. The maximum allowable power dissipation at any ambient temperature is P
±
5
30mA over long term may adversely affect reliability.
O
≤ 11.5V. For Sinking tests, 3.5V ≤ V
Sourcing Current vs. Output Voltage
Input Current vs. Temperature
O
= 12 V
O
≤ 7.5V.
PP
.
01171343
01171341
www.national.com
D
= (T
J(max)