LT1008CH Linear Technology, LT1008CH Datasheet
LT1008CH
Specifications of LT1008CH
Related parts for LT1008CH
LT1008CH Summary of contents
Page 1
... It plugs into and upgrades all standard LM108A/LM308A applications. For an internally compensated version with even lower offset voltage but otherwise similar performance see the LT1012. , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. 0. 10V ...
Page 2
... T = 45°C/W JMAX JA JC ORDER PART NUMBER LT1008MH LT1008CH OBSOLETE PACKAGES Consider Package for Alternate Source Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER V Input Offset Voltage OS Long-Term Input Offset Voltage Stability ...
Page 3
ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER CMRR Common Mode Rejection Ratio PSRR Power Supply Rejection Ratio Input Voltage Range V Output Voltage Swing OUT Slew Rate I Supply Current S indicates specifications which apply over the full operating temperature range of – ...
Page 4
LT1008 ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER i Input Noise Current Density n A Large-Signal Voltage Gain VOL CMRR Common Mode Rejection Ratio PSRR Power Supply Rejection Ratio Input Voltage Range V Output Voltage Swing OUT Slew Rate I Supply Current S ...
Page 5
FREQUE SATIO CIRCUITS Standard Compensation Circuit R1 R2 –V IN **BANDWIDTH AND SLEW RATE ARE PROPORTIONAL TO 1/C 2 – LT1008 OUT R1C ≥ ...
Page 6
LT1008 W U TYPICAL PERFOR A CE CHARACTERISTICS Supply Current vs Supply Voltage 500 450 400 25°C 125°C 350 –55°C 300 SUPPLY VOLTAGE (±V) 0.1Hz to 10Hz Noise T = 25° ±2V TO ±20V V ...
Page 7
W U TYPICAL PERFOR A CE CHARACTERISTICS Voltage Gain vs Load Resistance 10M = ±15V ±10V V O –55°C 3M 25°C 1M 125°C 300k 100k LOAD RESISTANCE (kΩ) 1008 G15 Large-Signal Transient ...
Page 8
LT1008 U U APPLICATIO S I FOR ATIO Achieving Picoampere/Microvolt Performance In order to realize the picoampere—microvolt level accu- racy of the LT1008, proper care must be exercised. For example, leakage currents in circuitry external to the op amp can ...
Page 9
U U APPLICATIO S I FOR ATIO 10Ω *DEVICE UNDER TEST NOTE: ALL CAPACITOR VALUES ARE FOR NONPOLARIZED CAPACITORS ONLY Frequency Compensation The LT1008 is externally frequency compensated with a single capacitor. The two standard compensation circuits shown earlier are ...
Page 10
LT1008 U U APPLICATIO S I FOR ATIO 30pF 10k 2 – LT1008 10k 3 + INPUT* 8 1000pF *SOURCE RESISTANCE ≤15k FOR STABILITY U TYPICAL APPLICATIO S 10k* 2 – INPUT LT1008 3 + Amplifier for Bridge Transducers + ...
Page 11
U TYPICAL APPLICATIO S Amplifier for Photodiode Sensor – λ LT1008 100pF 1% The LT1008 integrator extends low frequency range. Total dynamic range is 0.01Hz to 10kHz (or ...
Page 12
LT1008 U TYPICAL APPLICATIO S Precision, Fast Settling, Lowpass Filter 2 – 1.5M LT1008 INPUT 1μF 1 1000pF OPTO-MOS* 15V 15V LT311A – 4 –15V 1 100Ω 5 15V *OPTO-MOS SWITCH TYPE ...
Page 13
W W SCHE ATIC DIAGRA COMP1 1 22k 22k Q16 Q13 –INPUT Q10 Q39 +INPUT 3 Q18 Q17 – 4. COMP2 8 1.3k 4.2k Q14 3k Q22 ...
Page 14
LT1008 PACKAGE DESCRIPTIO 0.335 – 0.370 (8.509 – 9.398) DIA 0.305 – 0.335 (7.747 – 8.509) 0.040 (1.016) MAX SEATING PLANE 0.010 – 0.045* (0.254 – 1.143) 0.016 – 0.021** (0.406 – 0.533) * LEAD DIAMETER IS UNCONTROLLED BETWEEN THE ...
Page 15
... MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 16
... LT1004C-1.2 549Ω 549Ω 549Ω 549Ω 1008 TA11 COMMENTS Internally Compensated LT1008 Dual LT1012 Single SOT-23 Version of LT1884 Dual/Quad C Stable LOAD Dual/Quad Faster LT1881/LT1882 LT 0607 REV B • PRINTED IN THE USA © LINEAR TECHNOLOGY CORPORATION 1991 1008fb ...