MAX6897AALT+T Maxim Integrated Products, MAX6897AALT+T Datasheet - Page 7
![IC SEQUENCE/SUPERVISOR 6UDFN](/photos/6/95/69599/6-udfn_21-0147_sml.jpg)
MAX6897AALT+T
Manufacturer Part Number
MAX6897AALT+T
Description
IC SEQUENCE/SUPERVISOR 6UDFN
Manufacturer
Maxim Integrated Products
Type
Sequencerr
Datasheet
1.MAX6896PALTT.pdf
(15 pages)
Specifications of MAX6897AALT+T
Number Of Voltages Monitored
1
Output
Open Drain or Open Collector
Reset
Active High
Reset Timeout
Adjustable/Selectable
Voltage - Threshold
Adjustable/Selectable
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
6-µDFN
Output Type
Active High, Open Drain
Manual Reset
Not Resettable
Watchdog
No Watchdog
Battery Backup Switching
No Backup
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.5 V
Supply Current (typ)
10 uA
Maximum Power Dissipation
167.7 mW
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Power Fail Detection
No
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
MAX6897AALT+T
MAX6897AALT+TTR
MAX6897AALT+TTR
Connect the center point of a resistive divider to IN to
monitor external voltages (see R1 and R2 of the Typical
Operating Circuit ). IN has a rising threshold of V
0.5V and a falling threshold of 0.495V (5mV hysteresis).
When V
ENABLE is low) OUT goes high (OUT goes low) after
the programmed t
0.495V, OUT goes low (OUT goes high) after a 16µs
delay. IN has a maximum input current of 15nA so
large-value resistors are permitted without adding sig-
nificant error to the resistive divider.
When V
low), the internal 250nA current source begins charging
an external capacitor connected from CDELAY to GND.
When the voltage at CDELAY reaches 1V, the output
Figure 2. MAX6895A/MAX6897A Timing Diagram
ENABLE
V
OUT
CC
IN
IN
IN
rises above V
rises above V
_______________________________________________________________________________________
DELAY
Adjustable Delay (CDELAY)
V
UVLO
TH
period. When V
TH
with ENABLE high (ENABLE
and ENABLE is high (or
t
PROPA
Monitor Input (IN)
Sequencing/Supervisory Circuits
IN
falls below
TH
t
DL
=
V
TH
Ultra-Small, Adjustable
asserts (OUT goes high or OUT goes low). When the
output asserts, C
Adjust the delay (t
V
high (OUT going low) according to the equation:
where C
to GND.
For adjustable delay devices (A version), when V
0.5V and ENABLE goes from low to high (ENABLE
goes from high to low) the output asserts after a t
period. For nonadjustable delay devices (P version)
there is a 1µs propagation delay from when the enable
input is asserted to when the output asserts. Figures 2
through 5 show the timing diagrams for the adjustable
and fixed delay versions, respectively.
TH
(with ENABLE high or ENABLE low) to OUT going
t
V
DELAY
TH
CDELAY
t
DELAY
= C
is the external capacitor from CDELAY
CDELAY
DELAY
CDELAY
t
OFF
t < t
PROPA
) from when V
is immediately discharged.
x 4.0 x 10
t > t
PW
6
t
PROPA
+ 40µs
IN
rises above
DELAY
IN
>
7