MAX791CSE+ Maxim Integrated Products, MAX791CSE+ Datasheet
MAX791CSE+
Specifications of MAX791CSE+
Related parts for MAX791CSE+
MAX791CSE+ Summary of contents
Page 1
... SWT 8 DIP/SO/TSSOP MaxCap is a registered trademark of Cesiwid Inc. SuperCap is a registered trademark of Baknor Industries. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. ♦ Precision 4.65V Voltage Monitoring ♦ 200ms Power-OK / Reset Time Delay ♦ ...
Page 2
Microprocessor Supervisory Circuit ABSOLUTE MAXIMUM RATINGS Input Voltage (with respect to GND) V .......................................................................-0.3V to +6V CC VBATT..................................................................-0. All Other Inputs.....................................-0. Input Current V Peak ..........................................................................1. Continuous ............................................................250mA CC VBATT Peak ..................................................................250mA VBATT ...
Page 3
Microprocessor Supervisory Circuit ELECTRICAL CHARACTERISTICS (continued 4.75V to 5.5V, VBATT = 2.8V PARAMETER I BATT ON Output Low Voltage I Sink current BATT ON Output Short-Circuit Current Source current RESET, LOW-LINE, AND WATCHDOG TIMER – — ...
Page 4
Microprocessor Supervisory Circuit ELECTRICAL CHARACTERISTICS (continued 4.75V to 5.5V, VBATT = 2.8V PARAMETER V WDI Threshold Voltage IH (Note WDI = 0V WDI Input Current WDI = V POWER-FAIL COMPARATOR PFI Input ...
Page 5
Microprocessor Supervisory Circuit (T = +25°C, unless otherwise noted SUPPLY CURRENT vs. TEMPERATURE CC (NORMAL OPERATING MODE +5V CC VBATT = 2.8V 54 PFI -60 -30 0 ...
Page 6
Microprocessor Supervisory Circuit (T = +25°C, unless otherwise noted.) A BATTERY CURRENT vs. INPUT SUPPLY VOLTAGE VBATT = 2.8V OUT ( ...
Page 7
Microprocessor Supervisory Circuit PIN NAME 1 VBATT Backup-Battery Input. Connect to external battery or capacitor and charging circuit. Output Supply Voltage threshold. When V OUT CC Connect a 0.1µF capacitor from Input Supply Voltage—+5V ...
Page 8
Microprocessor Supervisory Circuit 150mV 4.65V VBATT CHIP-ENABLE OUTPUT CONTROL OUT 9 RESET MR GENERATION TIMEBASE FOR 8 RESET AND SWT WATCHDOG WATCHDOG 11 TRANSITION WDI DETECTOR 7 PFI 1.25V MAX791 4 GND ...
Page 9
Microprocessor Supervisory Circuit 15 RESET 10k MAX791 Figure 4. Adding an External Pull-Down Resistor Ensures – — — — — – Valid with V Down to GND CC The MAX791’s RESET output ensures that ...
Page 10
Microprocessor Supervisory Circuit +5V 3.6V *1µF +5V REACTIVATE *SETS Q HIGH ON POWER-UP Figure 6. Two Consecutive Watchdog Faults Latch the System in Reset Watchdog-Pulse Output As described in the preceding section, WDPO can be used as the clock input ...
Page 11
Microprocessor Supervisory Circuit V CC RESET THRESHOLD OUT 15µs 100µs RESET RESET Figure 7. Reset and Chip-Enable Timing enables the MAX791 to be used with most µPs high impedance (disabled mode) while RESET is ...
Page 12
Microprocessor Supervisory Circuit FROM REGULATED 3 2 SUPPLY OUT 0.1µF 0.1µF MAX791 1 VBATT 3.0V 15 RESET 10 LOWLINE 11 WDI GND OUT 0.1 µF VOLTAGE MAX791 1 REGULATOR VBATT ...
Page 13
Microprocessor Supervisory Circuit 1 VBATT MAX791 Figure 10. V and VBATT-to-V Switch CC OUT Battery On Output The Battery On (BATT ON) output indicates the status of the internal V /battery-switchover comparator, CC which controls the internal ...
Page 14
Microprocessor Supervisory Circuit + 1N4148 1 VBATT V OUT 0.47F MAX791 GND 4 Figure 12. SuperCap or MaxCap on VBATT Applications Information The MAX791 is not short-circuit protected. Shorting V to ground, other than power-up transients such ...
Page 15
Microprocessor Supervisory Circuit Rp* V OUT OUT MAX791 GND *MAXIMUM Rp VALUE DEPENDS ON THE NUMBER OF RAMs. MINIMUM Rp VALUE IS 1kΩ ACTIVE-HIGH CE LINES FROM LOGIC Figure 13. Alternate CE Gating Monitoring a Negative Voltage ...
Page 16
Microprocessor Supervisory Circuit + PFI MAX791 R2 GND V- +5V PFO 0V V TRIP 1.25 1. TRIP = R1 R2 NOTE NEGATIVE TRIP Figure 15. Monitoring a Negative Voltage close to ...
Page 17
Microprocessor Supervisory Circuit START SET WDI LOW SUBROUTINE OR PROGRAM LOOP, SET WDI HIGH RETURN END Figure 17. Watchdog Flow Diagram ______________________________________________________________________________________ Chip Topography V VBATT WDPO OUT V CC GND BATT ON PFO PFI SWT MR LOWLINE 0.07" (1.778mm) ...
Page 18
Microprocessor Supervisory Circuit (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages ...
Page 19
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 19 ____________________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 © 2005 Maxim Integrated Products ...