MCP111-300E/TO Microchip Technology, MCP111-300E/TO Datasheet - Page 3
![IC VOLT DET 2.93V LOW TO-92](/photos/7/50/75004/to-92_pkg_sml.jpg)
MCP111-300E/TO
Manufacturer Part Number
MCP111-300E/TO
Description
IC VOLT DET 2.93V LOW TO-92
Manufacturer
Microchip Technology
Type
Simple Reset/Power-On Resetr
Specifications of MCP111-300E/TO
Number Of Voltages Monitored
1
Output
Open Drain or Open Collector
Reset
Active Low
Voltage - Threshold
2.93V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-92-3 (Standard Body), TO-226
Threshold Voltage
2.93V
No. Of Supervisors / Monitors
1
Supply Voltage Range
1V To 5.5V
Reset Type
Active-Low / Open-Drain
Supply Current
1µA
Delay Time
100µs
Digital Ic Case Style
TO-92
Monitored Voltage
2.93 V
Manual Reset
Not Resettable
Watchdog
No Watchdog
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1 V
Supply Current (typ)
1.75 uA
Maximum Operating Temperature
+ 125 C
Mounting Style
Through Hole
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Reset Timeout
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
DC CHARACTERISTICS (CONTINUED)
© 2005 Microchip Technology Inc.
Electrical Specifications: Unless otherwise indicated, all limits are specified for V
T
Threshold Hysteresis
V
V
Open-drain High Voltage on Output
Open-drain Output Leakage Current
(MCP111 only)
Note 1:
min. = 1%, max = 6%)
A
OUT
OUT
= -40°C to +125°C.
Low-level Output Voltage
High-level Output Voltage
2:
3:
4:
Trip point is ±1.5% from typical value.
Trip point is ±2.5% from typical value.
This specification allows this device to be used in PICmicro
Serial Programming™ (ICSP™) feature (see device-specific programming specifications for voltage requirements).
This specification DOES NOT allow a continuous high voltage to be present on the open-drain output pin (V
total time that the V
V
0°C to 70°C (+25°C preferred). For additional information, please refer to Figure 2-28.
This parameter is established by characterization and is not 100% tested.
OUT
Parameters
pin should be limited to 2 mA. It is recommended that the device operational temperature be maintained between
MCP1XX-195
MCP1XX-240
MCP1XX-270
MCP1XX-290
MCP1XX-300
MCP1XX-315
MCP1XX-450
MCP1XX-475
OUT
pin can be above the maximum device operational voltage (5.5V) is 100 sec. Current into the
V
V
Sym
V
V
I
ODH
HYS
OD
OH
OL
V
DD
0.019
0.023
0.026
0.029
0.029
0.031
0.044
0.046
Min
—
—
—
– 0.6
®
microcontroller applications that require the In-Circuit
Typ
0.1
—
—
—
—
—
—
—
—
—
—
—
DD
13.5
0.139
0.158
0.174
0.176
0.185
0.263
0.278
0.114
Max
0.4
—
—
= 1V to 5.5V, R
(3)
Units
µA
V
V
V
V
V
V
V
V
V
V
V
MCP111/112
T
I
I
(push-pull output)
MCP111 only,
V
5.5V applied
current into pin limited to
2 mA, +25°C operation
recommended
Note 3, Note 4
PU
OL
OH
A
DD
= +25°C
= 100 k (only MCP111),
= 500 µA, V
= 1 mA, For only MCP112
= 3.0V, Time voltage >
Conditions
DS21889D-page 3
100s,
DD
= V
OUT
TRIP(MIN)
). The