DS1236S-10N Maxim Integrated Products, DS1236S-10N Datasheet
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS1236S-10N
Specifications of DS1236S-10N
Available stocks
Related parts for DS1236S-10N
DS1236S-10N Summary of contents
Page 1
FEATURES Holds microprocessor in check during power transients Halts and restarts an out-of-control microprocessor Monitors pushbutton for external override Warns microprocessor of an impending power failure Converts CMOS SRAM into nonvolatile memory Unconditionally write-protects memory when power supply is ...
Page 2
An internal watchdog timer can also force the reset outputs to the active state if the strobe input is not driven low prior to watchdog timeout. Reset control and wake-up/sleep control inputs ...
Page 3
POWER MONITOR The DS1236 employs a band gap voltage reference and a precision comparator to monitor the 5-volt supply ( microprocessor-based systems. When an out-of-tolerance condition occurs, the RST and CC outputs are driven to the active state. ...
Page 4
NON-MASKABLE INTERRUPT The DS1236 generates a non-maskable interrupt microprocessor. A precision comparator monitors the voltage level at the IN pin relative to a reference generated by the internal band gap. The IN pin is a high-impedance input allowing for a ...
Page 5
DS1236 FUNCTIONAL BLOCK DIAGRAM Figure 1 If the IN pin is connected to V CCO mode (RC=0). In the CMOS mode (RC=V produce a pulse on the pin. Given that any NMI the pin will remain high. ...
Page 6
This delay of write protection until the current memory cycle is completed prevents CE the corruption of data. If CEO unconditionally disabled within t maximum propagation delay of 20 ...
Page 7
NMI/FROM ST/INPUT Figure 3 POWER MONITOR, WATCHDOG Figure 4 PUSH BUTTON RESET TIMING Figure 5 NON-MASKABLE INTERRUPT Figure DS1236 ...
Page 8
EXAMPLE 1: 5 VOLT SUPPLY 10k OHM, V ∴ 4.80 = EXAMPLE 2: 12 VOLT SUPPLY 10k OHM, V ∴ 9.00 = NONVOLATILE SRAM Figure 10k X 2.54 10k R1 + 10k X ...
Page 9
When the RC pin is tied to ground, the DS1236 is designed to interface with NMOS processors which do not have the microamp currents required during a battery backed mode. Grounding the RC pin does, however, continue to support nonvolatile ...
Page 10
In this way, the NMI the supply voltage, as monitored by the IN pin, is above or below a selected operating value. This is illustrated in Figure 3. As discussed above, the RC pin determines the timing relationships ...
Page 11
Removal of the sleep mode by the pin threshold at V when the RC pin is tied high (CMOS mode). Subsequent power-up of the V TP with the RC pin tied high will activate the ...
Page 12
CMOS MODE POWER-DOWN ( Figure 10 CCO DS1236 ...
Page 13
NMOS MODE POWER-DOWN (RC = GND) Figure DS1236 ...
Page 14
NMOS MODE POWER-UP (RC = GND) Figure DS1236 ...
Page 15
CMOS MODE POWER-UP ( Figure 13 CCO DS1236 ...
Page 16
WAKE/SLEEP CONTROL Figure 14 OPTIONS FOR INVOKING WAKEUP Figure DS1236 ...
Page 17
ABSOLUTE MAXIMUM RATINGS* Voltage on V Pin Relative to Ground CC Voltage on I/O Relative to Ground Voltage on IN Pin Relative to Ground Operating Temperature Operating Temperature (Industrial Version) Storage Temperature Soldering Temperature * This is a stress rating ...
Page 18
PARAMETER Output Current @ 2.4V Power Sup. Trip Point Power Supply Trip (5% Option) IN Input Pin Current IN Input Trip Point AC ELECTRICAL CHARACTERISTICS PARAMETER V Fail Detect to RST, RST NMI TP RESET Active Time ...
Page 19
CAPACITANCE PARAMETER Input Capacitance Output Capacitance NOTES: 1. All voltages referenced to ground. A 0.1 μF capacitor is recommended between V 2. Measured with PF, CEO CCO the maximum average load which the DS1236 ...