MCP1726-3302E/MF Microchip Technology, MCP1726-3302E/MF Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP1726-3302E/MF
Manufacturer Part Number
MCP1726-3302E/MF
Description
IC LDO REG 1A 3.3V 8DFN
Manufacturer
Microchip Technology
Specifications of MCP1726-3302E/MF
Regulator Topology
Positive Fixed
Voltage - Output
3.3V
Voltage - Input
Up to 6V
Voltage - Dropout (typical)
0.22V @ 1A
Number Of Regulators
1
Current - Output
1A (Min)
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-DFN
Primary Input Voltage
6V
Output Voltage Fixed
3.3V
Dropout Voltage Vdo
220mV
No. Of Pins
8
Output Current
1A
Operating Temperature Range
-40°C To +125°C
Peak Reflow Compatible (260 C)
Yes
Number Of Outputs
1
Polarity
Positive
Input Voltage Max
6 V
Output Voltage
3.3 V
Output Type
Fixed
Dropout Voltage (max)
220 mV
Line Regulation
0.05 % / V
Load Regulation
0.5 %
Voltage Regulation Accuracy
2.5 %
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
MCP1726
Once the power good threshold (rising) has been
reached, the C
to 1.5V (typical, this level can vary between 1.4V and
1.75V across the input voltage range of the part). The
PWRGD output will transition high when the C
voltage has charged to 0.42V. If the output falls below
the power good threshold limit during the charging time
between 0.0V and 0.42V on the C
LAY
the timer. The C
put voltage of the LDO has once again risen above the
power good rising threshold. A timing diagram showing
C
FIGURE 4-4:
Diagram.
4.7
The SHDN input is an active-low input signal that turns
the LDO on and off. The SHDN threshold is a percent-
age of the input voltage. The typical value of this
shutdown threshold is 30% of V
maximum limits over the entire operating temperature
range of 45% and 15%, respectively.
The SHDN input will ignore low-going pulses (pulses
meant to shut down the LDO) that are up to 400 ns in
pulse width. If the shutdown input is pulled low for more
than 400 ns, the LDO will enter Shutdown mode. This
small bit of filtering helps to reject any system noise
spikes on the shutdown input signal.
On the rising edge of the SHDN input, the shutdown
circuitry has a 30 µs delay before allowing the LDO
output to turn on. This delay helps to reject any false
turn-on signals or noise on the SHDN input signal. After
the 30 µs delay, the LDO output enters its soft-start
period as it rises from 0V to its final regulation value. If
the SHDN input signal is pulled low during the 30 µs
delay period, the timer will be reset and the delay time
will start over again on the next rising edge of the
SHDN input. The total time from the SHDN input going
DS21936C-page 16
DELAY
V
0V
OUT
PWRGD
pin voltage will be pulled to ground, thus resetting
, PWRGD and V
T
PG
Shutdown Input (SHDN)
C
DELAY
DELAY
DELAY
C
V
DELAY
PWRGD_TH
pin charges the external capacitor
pin will be held low until the out-
C
OUT
Threshold (0.42V)
DELAY
1.5V (typ)
is shown in
and PWRGD Timing
IN
, with minimum and
DELAY
Figure
pin, the C
DELAY
4-4.
pin
DE-
high (turn-on) to the LDO output being in regulation is
typically 100 µs. See
the SHDN input.
FIGURE 4-5:
Diagram.
4.8
Dropout voltage is defined as the input-to-output
voltage differential at which the output voltage drops
2% below the nominal value that was measured with a
V
a very low dropout voltage specification of 220 mV
(typical) at 1A of output current. See the Electrical
Characteristics table for maximum dropout voltage
specifications.
The MCP1726 LDO operates across an input voltage
range of 2.3V to 6.0V and incorporates input Undervolt-
age Lockout (UVLO) circuitry that keeps the LDO
output voltage off until the input voltage reaches a
minimum of 2.18V (typical) on the rising edge of the
input voltage. As the input voltage falls, the LDO output
will remain on until the input voltage level reaches
2.04V (typical).
Since the MCP1726 LDO undervoltage lockout
activates at 2.04V as the input voltage is falling, the
dropout voltage specification does not apply for output
voltages that are less than 1.9V.
For high-current applications, voltage drops across the
PCB traces must be taken into account. The trace
resistances can cause significant voltage drops
between the input voltage source and the LDO. For
applications with input voltages near 2.3V, these PCB
trace voltage drops can sometimes lower the input
voltage enough to trigger a shutdown due to
undervoltage lockout.
R
V
SHDN
+ 0.5V differential applied. The MCP1726 LDO has
OUT
30 µs
Dropout Voltage and Undervoltage
Lockout
T
OR
70 µs
Figure 4-5
Shutdown Input Timing
© 2007 Microchip Technology Inc.
for a timing diagram of
400 ns (typ)