MIC2951-3.3YM Micrel Inc, MIC2951-3.3YM Datasheet - Page 7
![IC REG LDO 150MA 3.3V 8SOIC](/photos/6/50/65078/576-8-soic_sml.jpg)
MIC2951-3.3YM
Manufacturer Part Number
MIC2951-3.3YM
Description
IC REG LDO 150MA 3.3V 8SOIC
Manufacturer
Micrel Inc
Datasheet
1.MIC2951-03YM_TR.pdf
(20 pages)
Specifications of MIC2951-3.3YM
Regulator Topology
Positive Fixed or Adjustable
Voltage - Output
3.3V, 1.24 ~ 29 V
Voltage - Input
2 ~ 30 V
Voltage - Dropout (typical)
0.32V @ 150mA
Number Of Regulators
1
Current - Output
150mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Other names
576-1151
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MIC2951-3.3YM
Manufacturer:
MICREL/麦瑞
Quantity:
20 000
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating
11. Line regulation for the MIC2951 is tested at 150°C for I
12. Dropout voltage is defined as the input to output differential at which the output voltage drops 100mV below its nominal value measured at 1V
13. Thermal regulation is defined as the change in output voltage at a time “t” after a change in power dissipation is applied, excluding load or line
14. V
15. Comparator thresholds are expressed in terms of a voltage differential at the FB terminal below the nominal reference voltage measured at 6V input.
16. Specification for packaged product only.
Micrel, Inc.
Parameter
Shutdown Input Logic Voltage
Shutdown Input Current
Regulator Output Current
in Shutdown
February 2010
Exceeding the absolute maximum rating may damage the device.
The device is not guaranteed to function outside its operating rating.
Devices are ESD sensitive. Handling precautions are recommended.
The junction-to-ambient thermal resistance of the TO-92 package is 180°C/W with 0.4” leads and 160°C/W with 0.25” leads to a PC board. The
thermal resistance of the 8-pin DIP package is 105°C/W junction-to-ambient when soldered directly to a PC board. Junction-to-ambient thermal
resistance for the SOIC (M) package is 160°C/W. Junction-to-ambient thermal resistance for the MM8™ (MM) is 250°C/W.
The maximum positive supply voltage of 60V must be of limited duration (≤100ms) and duty cycle (≤1%). The maximum continuous supply voltage
is 30V.
When used in dual-supply systems where the output terminal sees loads returned to a negative supply, the output voltage should be diode-clamped
to ground.
V
Additional conditions for 8-pin devices are V
Output or reference voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range.
effects are covered in the specification for thermal regulation.
See Typical Performance Characteristics for line regulation versus temperature and load current.
differential. At very low values of programmed output voltage, the minimum input supply voltage of 2V (2.3V over temperature) must be taken into
account.
regulation effects. Specifications are for a 50mA load pulse at V
To express these thresholds in terms of output voltage change, multiply by the error amplifier gain = V
programmed output voltage of 5V, the error output is guaranteed to go low when the output drops by 95mV x 5V/1.235V = 384mV. Thresholds
remain constant as a percent of V
SHDN
REF
≤ V
≥ 2V, V
OUT
≤ (V
IN
≤ 30V, V
IN
– 1 V), 2.3V ≤ V
OUT
= 0, with the FB pin connected to TAP.
OUT
IN
Condition
MIC295x-02/-05 (±0.5%)
Low
High
MIC295x-03/-06 (±1%)
Low
High
MIC2951-3.3 (±1%)
Low
High
MIC2951-4.8 (±1%)
Low
High
V
V
Note 7
≤ 30V, 100µA < I
SHUTDOWN
SHUTDOWN
as V
OUT
FB
is varied, with the dropout warning occurring at typically 5% below nominal, 7.5% guaranteed.
= 5V, TAP and OUT connected to SNS (V
= 2.4V
= 30V
L
≤ 150mA, T
L
= 1mA. For I
IN
J
= 30V (1.25W pulse) for t = 10ms.
≤ T
L
= 100µA and T
JMAX
7
.
J
= 125°C, line regulation is guaranteed by design to 0.2%.
OUT
= 5V) and V
OUT
SHDN
Min
/V
2.0
2.0
2.0
2.0
REF
≤ 0.8V.
= (R1 + R2)/R2. For example, at a
Typ
450
1.3
1.3
1.3
1.3
30
3
Max
100
600
750
0.7
0.7
0.7
0.7
50
10
20
MIC2950/2951
M9999-021610
Units
µA
µA
µA
µA
µA
µA
V
V
V
V
V
V
V
V
V
V
V
V