LP38693MP-3.3/NOPB National Semiconductor, LP38693MP-3.3/NOPB Datasheet - Page 5
![IC REG LDO 500MA 3.3V SOT223-4](/photos/12/65/126584/pkg_mp05a_sml.jpg)
LP38693MP-3.3/NOPB
Manufacturer Part Number
LP38693MP-3.3/NOPB
Description
IC REG LDO 500MA 3.3V SOT223-4
Manufacturer
National Semiconductor
Series
PowerWise®r
Type
Linearr
Datasheet
1.LP38693-ADJEV.pdf
(16 pages)
Specifications of LP38693MP-3.3/NOPB
Regulator Topology
Positive Fixed
Voltage - Output
3.3V
Voltage - Input
Up to 10V
Voltage - Dropout (typical)
0.33V @ 500mA
Number Of Regulators
1
Current - Output
500mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
SOT-223 (4 leads + Tab)
Package
5SOT-223
Function
LDO
Number Of Outputs
1
Input Voltage Range
10 to 2.7 V
Output Voltage
3.3 V
Maximum Output Current
0.5 A
Output Type
Fixed
Accuracy
±2 %
Typical Dropout Voltage @ Current
0.065@100mA|0.33@500mA V
Polarity
Positive
For Use With
LP38693-ADJEV - BOARD EVAL 500MA LDO REG ADJLP38693EVAL - BOARD EVALUATION LP38693
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Other names
LP38693MP-3.3
LP38693MP-3.3TR
LP38693MP-3.3TR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LP38693MP-3.3/NOPB
Manufacturer:
TI
Quantity:
136
Part Number:
LP38693MP-3.3/NOPB
Manufacturer:
TI/德州仪器
Quantity:
20 000
e
V
V
I
EN
n
O
EN
Note 1: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Operating ratings indicate conditions for which the device
is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications, see Electrical Characteristics. Specifications do not
apply when operating the device outside of its rated operating conditions.
Note 2: At elevated temperatures, device power dissipation must be derated based on package thermal resistance and heatsink values (if a heatsink is used).
The junction-to-ambient thermal resistance ( θ
copper area (less than 0.1 square inch). If one square inch of copper is used as a heat dissipator for the TO-252, the θ
SOT-223 package has a θ
when soldered to a copper area of one square inch. The θ
of thermal vias used (refer to application note AN-1187 and the
to exceed specified limits, the device will go into thermal shutdown.
Note 3: ESD is tested using the human body model which is a 100pF capacitor discharged through a 1.5k resistor into each pin.
Note 4: Typical numbers represent the most likely parametric norm for 25°C operation.
Note 5: If used in a dual-supply system where the regulator load is returned to a negative supply, the output pin must be diode clamped to ground.
Note 6: Output voltage line regulation is defined as the change in output voltage from nominal value resulting from a change in input voltage.
Note 7: Output voltage load regulation is defined as the change in output voltage from nominal value as the load current increases from 1mA to full load.
Note 8: Dropout voltage is defined as the minimum input to output differential required to maintain the output within 100mV of nominal value.
Symbol
(LEAK)
Output Noise
Output Leakage Current
Enable Voltage (LP38693 Only)
Enable Pin Leakage (LP38693
Only)
J-A
of approximately 125°C/W when soldered down to a minimum sized pattern (less than 0.1 square inch) and approximately 70°C/W
Parameter
J-A
) for the TO-252 is approximately 90°C/W for a PC board mounting with the device soldered down to minimum
J-A
BW = 10Hz to 10kHz
V
V
Output = OFF
Output = ON, V
Output = ON, V
Output = ON, V
V
values for the LLP package are also dependent on trace area, copper thickness, and the number
O
O
EN
LLP MOUNTING
= 3.3V
= V
= 0V or 10V, V
O
(NOM) + 1V @ 10V
Conditions
5
IN
IN
IN
section in this datasheet). If power dissipation causes the junction temperature
= 4V
= 6V
= 10V
IN
= 10V
IN
Min
1.8
3.0
4.0
-1
J-A
(Note
drops to approximately 50°C/W. The
0.001
Typ
0.7
0.5
4)
Max
0.4
12
1
www.national.com
µV/
Units
µA
µA
V