AP7115-35WG-7 Diodes Inc, AP7115-35WG-7 Datasheet - Page 8

• Manufacturer Part Number: AP7115-35WG-7
• Description: IC REG LDO 150MA 3.5V SOT-25
• Manufacturer: Diodes Inc

Specifications of AP7115-35WG-7

• Regulator Topology: Positive Fixed
• Voltage - Output: 3.5V
• Voltage - Input: Up to 5.5V
• Voltage - Dropout (typical): 0.2V @ 150mA
• Number Of Regulators: 1
• Current - Output: 150mA (Max)
• Current - Limit (min): 200mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: SOT-25
• Number Of Outputs: 1
• Polarity: Positive
• Input Voltage Max: 5.5 V
• Output Voltage: 3.5 V
• Output Type: Fixed
• Dropout Voltage (max): 0.3 V at 150 mA
• Output Current: 150 mA
• Line Regulation: 0.1 % / V
• Load Regulation: 10 mV
• Voltage Regulation Accuracy: 2 %
• Maximum Power Dissipation: 0.5 W
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Application Note
An 1uF input capacitor is required between the AP7115 input pin
and GND.
There are no requirements for the ESR on input capacitor, but
tolerance and temperature coefficient must be considered.
The AP7115 can work with very small ceramic output capacitors
(1uF or greater). Higher capacitance values help to improve
transient. The output capacitor’s ESR is critical because it from a
zero to provide phase lead which is required for loop stability.
Figure below is Cout ESR vs. Load Current.
0.1uF bypass capacitor Between BP pin and GND can reduces
output voltage noise.
The AP7115 is shutdown by pulling the EN pin low, and turned on
by driving the input high. If the shutdown feature is not required,
the EN pin should be tied to VIN to keep the regulator on at all
times.
V
The AP7115 monitors and controls the PMOS’ gate voltage,
limiting the output current to 250mA(typ.). The output can be
shorted to ground for an indefinite period of time without
damaging the part.
AP7115 Rev. 10
DROPOUT
0.01
100
Input Capacitor
Output Capacitor
Band-Gap Bypass Capacitor
Shutdown Input Operation
Dropout Voltage
Current Limit
0.1
10
1
＝V
0
AP7115 Region of Stable Cout ESR vs.
IN
－V
20
OUT
40
＝R
Load Current (mA)
Load Current
60
DS(ON)
Stable
80
×I
OUT
100
120
150mA LOW DROPOUT LINEAR REGULATOR WITH
140
www.diodes.com
160
8 of 11
Optimum performance can only be achieved when the device is
mounted on a PC board according to the diagram below:
Thermal Shutdown Protection limits power dissipation in AP7115.
When the operation junction temperature exceeds 155°C, the
Over Temperature Protection circuit starts the thermal shutdown
function and turns the pass element off. The pass element turn
on again after the junction temperature cools by 30°C. For
continuous operation, do not exceed absolute maximum
operation junction temperature 125°C. The power dissipation
definition in device is:
P
The maximum power dissipation depends on the thermal
resistance of IC package, PCB layout, the rate of surroundings
airflow and temperature difference between junction to ambient.
The maximum power dissipation can be calculated by the
following formula:
P
Where T
125°C, T
to ambient thermal resistance.
D
D(MAX)
= (V
PCB Layout
Thermal Considerations
A
IN
= ( T
J(MAX)
is the ambient temperature and the θ
− V
J(MAX)
is the maximum operation junction temperature
OUT
) x I
- T
OUT
A
) / θ
+ V
JA
IN
x I
Q
©
AP7115
SHUTDOWN
Diodes Incorporated
JA
MAY 2009
is the junction