TC2055-3.0VCTTR Microchip Technology, TC2055-3.0VCTTR Datasheet - Page 3

• Manufacturer Part Number: TC2055-3.0VCTTR
• Description: IC CMOS LDO 3.0V 100MA SOT23A-5
• Manufacturer: Microchip Technology

Specifications of TC2055-3.0VCTTR

• Regulator Topology: Positive Fixed
• Voltage - Output: 3V
• Voltage - Input: Up to 6V
• Voltage - Dropout (typical): 0.09V @ 100mA
• Number Of Regulators: 1
• Current - Output: 100mA (Min)
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-5, SC-74A, SOT-25
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Limit (min): -
• Other names: TC20553.0VCTTR

1.0
Absolute Maximum Ratings †
Input Voltage ......................................................... 6.5V
Output Voltage ............................... (-0.3) to (V
Operating Temperature .................. -40°C < T
Storage Temperature ......................... -65°C to +150°C
Maximum Voltage on Any Pin ........ V
ELECTRICAL SPECIFICATIONS
© 2009 Microchip Technology Inc.
Electrical Specifications: Unless otherwise noted, V
BOLDFACE type specifications apply for junction temperature of -40°C to +125°C.
Input Operating Voltage
Maximum Output Current
Output Voltage
V
Coefficient
Line Regulation
Load Regulation
Dropout Voltage, Note 7
Supply Current
Shutdown Supply Current
Power Supply Rejection
Ratio
Output Short Circuit Current
Note 1:
OUT
Temperature
2:
3:
4:
5:
6:
7:
8:
9:
10: Hysteresis voltage is referenced by V
11: Time required for V
Parameter
ELECTRICAL
CHARACTERISTICS
The minimum V
V
TCV
Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested
over a load range from 1.0 mA to the maximum specified output current. Changes in output voltage due to heating
effects are covered by the thermal regulation specification.
Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal
value at a 1V differential.
Thermal Regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied,
excluding load or line regulation effects. Specifications are for a current pulse equal to I
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction tem-
perature and the thermal resistance from junction-to-air (i.e. T
R
is the regulator output voltage setting. For example: V
OUT
=
(
-----------------------------------------------------------------------------------------
V
OUTMAX
IN
V
has to meet two conditions: V
OUT
I
TCV
IN
ΔV
ΔV
OUT MAX
I
PSRR
OUT SC
V
V
Sym
I
ΔV
– V
INSD
V
V
I
OUT
OUT
OUT
OUT
IN
IN
OUT
to reach 95% of V
OUT
IN
–
OUT
V
/
/
OUTMIN
×
IN
ΔT
V
+0.3V to -0.3V
R
Min
100
150
-1.0
-2.0
160
2.7
- 2.0% V
50
—
—
—
—
—
—
—
—
—
—
)
×
R
J
.
IN
< 125°C
10
6
IN
+ 0.3)
R
(output voltage setting), after V
= V
R
0.05
0.33
0.43
0.05
Typ
140
300
± 0.4% V
20
40
45
90
55
50
R
—
—
—
—
2
IN
+ 1V, I
= 2.7V and V
L
R
R
= 100 µA, C
† Notice: Stresses above those listed under “Absolute
Maximum Ratings” may cause permanent damage to
the device. These are stress ratings only and functional
operation of the device at these or any other conditions
above those indicated in the operation sections of the
specifications is not implied. Exposure to Absolute
Maximum Rating conditions for extended periods my
affect device reliability.
Max
+1.0
+2.0
140
210
= 1.8V, 2.7V, 2.8V, 2.85V, 3.0V, 3.3V.
+ 2.0%
6.0
0.5
0.5
70
80
—
—
—
—
—
—
—
—
A
, T
IN
J
TC2054/2055/2186
, θ
= V
ppm/°C Note 3
JA
Units
L
mA
mV
mA
R
µA
µA
dB
%
%
).
= 3.3 µF, SHDN > V
V
V
+ V
SHDN
DROPOUT
Note 1
TC2054
TC2055
TC2186
Note 2
(V
TC2054;TC2055 I
TC2186
Note 6
TC2015; TC2185 I
TC2185
Note 7
SHDN = V
SHDN = 0V
F
V
RE
OUT
R
is switched from 0 to V
+ 1V) < V
≤ 100 kHz
= 0V
.
MAX
IH
, I
IH
IN
L
at V
Conditions
=0
, T
< 6V
I
L
A
L
IN
= 0.1 mA to I
I
I
I
= 0.1 mA to I
= +25°C.
L
L
L
L
= 6V for T = 10 ms.
= 100 µA
= 50 mA
= 100 mA
= 150 mA
DS21663D-page 3
IN
.
OUT MAX
OUT MAX