LT1129CT#06PBF Linear Technology, LT1129CT#06PBF Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LT1129CT#06PBF
Manufacturer Part Number
LT1129CT#06PBF
Description
IC REG LDO ADJ 0.7A TO220-5
Manufacturer
Linear Technology
Datasheet
1.LT1129CT06PBF.pdf
(16 pages)
Specifications of LT1129CT#06PBF
Regulator Topology
Positive Adjustable
Voltage - Output
3.8 ~ 30 V
Voltage - Input
4.15 ~ 30 V
Voltage - Dropout (typical)
0.45V @ 700mA
Number Of Regulators
1
Current - Output
700mA
Operating Temperature
0°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-220-5 (Bent and Staggered Leads)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LT1129/LT1129-3.3/LT1129-5
APPLICATIONS INFORMATION
Adjustable Operation
The adjustable version of the LT1129 has an output voltage
range of 3.75V to 30V. The output voltage is set by the
ratio of two external resistors as shown in Figure 2. The
device servos the output voltage to maintain the voltage
at the adjust pin at 3.75V. The current in R1 is then equal
to 3.75V/R1. The current in R2 is equal to the sum of the
current in R1 and the adjust pin bias current. The adjust
pin bias current, 150nA at 25°C, fl ows through R2 into the
adjust pin. The output voltage can be calculated according
to the formula in Figure 2. The value of R1 should be less
than 400k to minimize errors in the output voltage caused
by the adjust pin bias current. Note that in shutdown the
output is turned off and the divider current will be zero.
Curves of Adjust Pin Voltage vs Temperature and Adjust
Pin Bias Current vs Temperature appear in the Typical
Performance Characteristics. The reference voltage at
the adjust pin has a positive temperature coeffi cient of
approximately 15ppm/°C. The adjust pin bias current has
a negative temperature coeffi cient. These effects are small
and will tend to cancel each other.
The adjustable device is specifi ed with the adjust pin tied
to the output pin. This sets the output voltage to 3.75V.
Specifi cations for output voltages greater than 3.75V will
be proportional to the ratio of the desired output voltage
to 3.75V (V
output current change of 1mA to 700mA is – 6mV typical at
V
10
OUT
3.75V
= 3.75V. At V
12V
OUT
V
V
I
OUTPUT RANGE = 3.75V to 30V
ADJ
OUT
ADJ
• –6mV
/3.75V). For example: load regulation for an
Figure 2. Adjustable Operation
(
= 150nA at 25°C
= 3.75V
= 3.75V 1 +
IN
SHDN
OUT
(
LT1129
GND
)
= 12V, load regulation would be:
R2
R1
= –19mV
)
(
+ I
OUT
ADJ
(
ADJ
• R2
)
)
R1
R2
+
112935 F02
V
OUT
Thermal Considerations
The power handling capability of the device will be limited
by the maximum rated junction temperature (125°C). The
power dissipated by the device will be made up of two
components:
1. Output current multiplied by the input/output voltage
2. Ground pin current multiplied by the input voltage:
The ground pin current can be found by examining the
Ground Pin Current curves in the Typical Performance
Characteristics. Power dissipation will be equal to the
sum of the two components listed above.
The LT1129 series regulators have internal thermal
limiting designed to protect the device during overload
conditions. For continuous normal load conditions the
maximum junction temperature rating of 125°C must not
be exceeded. It is important to give careful consideration
to all sources of thermal resistance from junction to ambi-
ent. Additional heat sources mounted nearby must also be
considered.
For surface mount devices heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Experiments have shown that the
heat spreading copper layer does not need to be electri-
cally connected to the tab of the device. The PC material
can be very effective at transmitting heat between the pad
area, attached to the tab of the device, and a ground or
power plane layer either inside or on the opposite side of
the board. Although the actual thermal resistance of the
PC material is high, the length/area ratio of the thermal
resistor between layers is small. Copper board stiffeners
and plated through holes can also be used to spread the
heat generated by power devices.
The following tables list thermal resistances for each
package. For the TO-220 package, thermal resistance
is given for junction-to-case only since this package
is usually mounted to a heat sink. Measured values of
thermal resistance for several different board sizes and
copper areas are listed for each package. All measure-
ments were taken in still air on 3/32" FR-4 board with 1-oz
differential: I
I
GND
• V
IN
.
OUT
• (V
IN
– V
OUT
), and
112935ff