LT1963ES8-3.3#PBF Linear Technology, LT1963ES8-3.3#PBF Datasheet
LT1963ES8-3.3#PBF
Specifications of LT1963ES8-3.3#PBF
Available stocks
Related parts for LT1963ES8-3.3#PBF
LT1963ES8-3.3#PBF Summary of contents
Page 1
... The LT1963 regulators are available in 5-lead TO-220, DD, 3-lead SOT-223, 8-lead SO, and Exposed Pad 16-lead TSSOP packages. , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents, including 6118263, 6144250. 400 ...
Page 2
... W JMAX JA ORDER PART NUMBER ORDER PART NUMBER LT1963ET LT1963ET-1.5 LT1963ET-1.8 LT1963ET-2.5 LT1963ET-3.3 OUT GND IN ORDER PART NUMBER 196315 LT1963ES8 196318 LT1963ES8-1.5 196325 LT1963ES8-1.8 196333 LT1963ES8-2.5 LT1963ES8-3.3 TOP VIEW GND 1 16 GND OUT OUT *PIN 6 = SENSE FOR LT1963-1.5/ 17 LT1963-1.8/LT1963-2.5/ OUT ...
Page 3
ELECTRICAL CHARACTERISTICS The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are T PARAMETER CONDITIONS Minimum Input Voltage (Notes 4,12) I LOAD I LOAD Regulated Output Voltage (Note 5) LT1963-1.5 LT1963-1.8 LT1963-2.5 LT1963-3.3 ADJ Pin ...
Page 4
LT1963 Series ELECTRICAL CHARACTERISTICS The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are T PARAMETER CONDITIONS Current Limit Input Reverse Leakage Current (Note 13 Packages V ST ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS Typical Dropout Voltage 500 450 400 350 T = 125°C J 300 250 T = 25°C 200 J 150 100 0.8 1.2 1.4 0.2 0.4 0.6 1.0 1.6 OUTPUT CURRENT ...
Page 6
LT1963 Series W U TYPICAL PERFOR A CE CHARACTERISTICS LT1963-1.5 Quiescent Current 25° ∞ SHDN ...
Page 7
W U TYPICAL PERFOR A CE CHARACTERISTICS LT1963 GND Pin Current 25° SHDN IN *FOR V = 1.21V 8 OUT R = 4.33 300mA 12.1, ...
Page 8
LT1963 Series W U TYPICAL PERFOR A CE CHARACTERISTICS SHDN Pin Input Current 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0 SHDN PIN VOLTAGE (V) 1963 ...
Page 9
W U TYPICAL PERFOR A CE CHARACTERISTICS LT1963 Minimum Input Voltage 3 500mA L 2 100mA L 1.5 1.0 0.5 0 – 100 125 –25 0 TEMPERATURE (°C) ...
Page 10
LT1963 Series CTIO S OUT: Output. The output supplies power to the load. A minimum output capacitor of 10µF is required to prevent oscillations. Larger output capacitors will be required for applications with large transient ...
Page 11
U U APPLICATIO S I FOR ATIO The LT1963 series are 1.5A low dropout regulators opti- mized for fast transient response. The devices are capable of supplying 1. dropout voltage of 350mV. The low operating quiescent current (1mA) ...
Page 12
LT1963 Series U U APPLICATIO S I FOR ATIO 20 BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10µF 0 X5R –20 –40 –60 Y5V –80 –100 BIAS VOLTAGE (V) Figure 3. Ceramic ...
Page 13
U U APPLICATIO S I FOR ATIO Thermal Considerations The power handling capability of the device is limited by the maximum rated junction temperature (125°C). The power dissipated by the device is made up of two components: 1. Output current ...
Page 14
LT1963 Series U U APPLICATIO S I FOR ATIO Using a DD package, the thermal resistance will be in the range of 23°C/W to 33°C/W depending on the copper area. So the junction temperature rise above ambient will be approximately ...
Page 15
U TYPICAL APPLICATIO S SCR Pre-Regulator Provides Efficiency Over Line Variations L2 10VAC AT 115V IN 90-140 VAC 10VAC AT 115V IN 1N4002 1N4002 “SYNC” 1N4002 2.4k TO ALL “+V” + POINTS 22µF 750Ω V > 3. 500µH ...
Page 16
LT1963 Series PACKAGE DESCRIPTIO .060 .256 (1.524) (6.502) .060 .183 (1.524) (4.648) .075 (1.905) .300 (7.620) BOTTOM VIEW OF DD PAK HATCHED AREA IS SOLDER PLATED COPPER HEAT SINK .067 RECOMMENDED SOLDER PAD LAYOUT NOTE: 1. DIMENSIONS IN INCH/(MILLIMETER) 2. ...
Page 17
PACKAGE DESCRIPTIO .050 BSC .245 MIN .030 ±.005 TYP RECOMMENDED SOLDER PAD LAYOUT .010 – .020 (0.254 – 0.508) .008 – .010 (0.203 – 0.254) (0.406 – 1.270) NOTE: 1. DIMENSIONS IN 2. DRAWING NOT TO SCALE 3. THESE DIMENSIONS ...
Page 18
LT1963 Series PACKAGE DESCRIPTIO .264 – .287 (6.70 – 7.30) .130 – .146 (3.30 – 3.71) .0905 (2.30) BSC .071 (1.80) MAX 0.390 – 0.415 (9.906 – 10.541) 0.230 – 0.270 (5.842 – 6.858) 0.460 – 0.500 (11.684 – 12.700) ...
Page 19
... DIMENSIONS ARE IN 3. DRAWING NOT TO SCALE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights Package 16-Lead Plastic TSSOP (4 ...
Page 20
... MS8 Package 1.21V 0.34V 1mA, I <1µ –1.21V 0.34V 30µ 3µ 0.20 0.15V 120µA, I <3µ 1.22V 0.30V 40µA, I <1µ 1.22V 0.30V 60µA, I <1µ 1.23V 0.13V 12mA 25µ 1105 • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2005 1963fc ...