LT1521CMS8 Linear Technology, LT1521CMS8 Datasheet - Page 4

IC LDO REG W/SHTDWN ADJ 8-MSOP

LT1521CMS8

Manufacturer Part Number
LT1521CMS8
Description
IC LDO REG W/SHTDWN ADJ 8-MSOP
Manufacturer
Linear Technology
Datasheet

Specifications of LT1521CMS8

Regulator Topology
Positive Adjustable
Voltage - Output
3.8 ~ 20 V
Voltage - Input
4.3 ~ 20 V
Voltage - Dropout (typical)
0.5V @ 300mA
Number Of Regulators
1
Current - Output
300mA
Current - Limit (min)
320mA
Operating Temperature
0°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
LT1521CMS8
Manufacturer:
LT
Quantity:
5 321
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
LT1521CMS8
Manufacturer:
LT
Quantity:
10 000
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
LT1521CMS8-3
Manufacturer:
LT
Quantity:
10 000
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
LT1521CMS8-3.3
Manufacturer:
LT
Quantity:
10 000
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
LT1521CMS8-5
Manufacturer:
LT
Quantity:
10 000
Price:
TYPICAL PERFORMANCE CHARACTERISTICS
LT1521/LT1521-3
LT1521-3.3/LT1521-5
ELECTRICAL CHARACTERISTICS
temperature range, otherwise specifications are at T
PARAMETER
Input Reverse Leakage Current
Reverse Output Current (Note 11)
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: The shutdown pin input voltage rating is required for a low
impedance source. Internal protection devices connected to the shutdown
pin will turn on and clamp the pin to approximately 7V or – 0.6V. This
range allows the use of 5V logic devices to drive the pin directly. For high
impedance sources or logic running on supply voltages greater than 5.5V,
the maximum current driven into the shutdown pin must be limited to less
than 5mA.
Note 3: For junction temperatures greater than 110 C, a minimum load of
1mA is recommended. For T
may increase by 1%.
Note 4: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specification will not apply for
all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
4
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Guaranteed Dropout Voltage
0
= TEST POINTS
50
T
J
OUTPUT CURRENT (mA)
125 C
100
T
150
J
J
> 110 C and I
25 C
200
W
250
LT1521 • TPC01
OUT
U
CONDITIONS
V
LT1521-3
LT1521-3.3
LT1521-5
LT1521 (Note 5)
IN
300
< 1mA, output voltage
= – 20V, V
0.8
0.5
0.4
0.3
0.2
0.7
0.6
0.1
OUT
0
–50
A
Dropout Voltage
= 25 C.
= 0V
V
V
V
V
–25
OUT
OUT
OUT
OUT
The
= 3V, V
= 3.3V, V
= 5V, V
= 3.8V, V
0
TEMPERATURE ( C)
I
LOAD
I
LOAD
denotes the specifications which apply over the full operating
IN
IN
25
I
= 100mA
IN
IN
LOAD
= 300mA
I
< 3V, T
< 5V, T
LOAD
Note 5: The LT1521 (adjustable version) is tested and specified with the
adjust pin connected to the output pin.
Note 6: Dropout voltage is the minimum input/output voltage required to
maintain regulation at the specified output current. In dropout the output
voltage will be equal to: (V
Note 7: Ground pin current is tested with V
current source load. This means the device is tested while operating in its
dropout region. This is the worst-case ground pin current. The ground pin
current will decrease slightly at higher input voltages.
Note 8: Adjust pin bias current flows into the adjust pin.
Note 9: Shutdown pin current at V
pin.
Note 10: Quiescent current in shutdown is equal to the total sum of the
shutdown pin current (2 A) and the ground pin current (4 A).
Note 11: Reverse output current is tested with the input pin grounded and
the output pin forced to the rated output voltage. This current flows into
the output pin and out of the ground pin.
< 3.3V, T
< 3.75V, T
50
= 50mA
= 1mA
J
J
I
LOAD
= 25 C
= 25 C
75
J
J
= 25 C
= 150mA
LT1521 • TPC02
= 25 C
100
125
IN
– V
15.0
12.5
10.0
7.5
5.0
2.5
0
MIN
DROPOUT
–50
Quiescent Current
SHDN
V
R
I
–25
LOAD
IN
L
= 0V flows out of the shutdown
=
)
= 6V
= 0
IN
0
TEMPERATURE ( C)
TYP
= V
5
5
5
5
OUT
25
(nominal) and a
50
V
V
SHDN
SHDN
MAX
1.0
10
10
10
10
75
= 0V
= OPEN
LT1521 • TPC03
100
1521335fb
UNITS
mA
125
A
A
A
A

Related parts for LT1521CMS8