LT1529CQ-5 Linear Technology, LT1529CQ-5 Datasheet - Page 10
![IC LDO W/SHTDWN 5V 3A DDPAK-5](/photos/7/55/75544/161-5-dd_sml.jpg)
LT1529CQ-5
Manufacturer Part Number
LT1529CQ-5
Description
IC LDO W/SHTDWN 5V 3A DDPAK-5
Manufacturer
Linear Technology
Datasheet
1.LT1529CTPBF.pdf
(12 pages)
Specifications of LT1529CQ-5
Regulator Topology
Positive Fixed
Voltage - Output
5V
Voltage - Input
Up to 15V
Voltage - Dropout (typical)
0.6V @ 3A
Number Of Regulators
1
Current - Output
3A
Current - Limit (min)
3.2A
Operating Temperature
0°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
TO-263-5, D²Pak (5 leads + Tab), TO-263BA
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LT1529CQ-5
Manufacturer:
ALPHA
Quantity:
180
Part Number:
LT1529CQ-5
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1529CQ-5#PBF
Manufacturer:
LT/凌特
Quantity:
20 000
Part Number:
LT1529CQ-5#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LT1529CQ-5.0
Manufacturer:
LT
Quantity:
2
LT1529
LT1529-3.3/LT1529-5
micropower device and output transient response will be
a function of output capacitance. See the Transient Re-
sponse curves in the Typical Performance Characteristics.
Larger values of output capacitance will decrease the peak
deviations and provide improved output transient re-
sponse for larger load current deltas. Bypass capacitors,
used to decouple individual components powered by the
LT1529, will increase the effective value of the output
capacitor.
Protection Features
The LT1529 incorporates several protection features which
make it ideal for use in battery-powered circuits. In addi-
tion to the normal protection features associated with
monolithic regulators, such as current limiting and ther-
mal limiting, the device is protected against reverse input
voltages, and reverse voltages from output to input.
Current limit protection and thermal overload protection
are intended to protect the device against current overload
conditions at the output of the device. For normal opera-
tion, the junction temperature should not exceed 125°C.
The input of the device will withstand reverse voltages of
15V. Current flow into the device will be limited to less than
1mA (typically less than 100µA) and no negative voltage
will appear at the output. The device will protect both itself
and the load. This provides protection against batteries
that can be plugged in backwards.
For fixed voltage versions of the device, the SENSE pin is
internally clamped to one diode drop below ground. For
the adjustable version of the device, the OUTPUT pin is
internally clamped at one diode drop below ground. If the
Table 2. Fault Conditions
A
10
– 15V < V
< V
< V
PPLICATI
OUT
OUT
V
≤ 0.8V
≤ 0.8V
>1.5V
Open
Open
IN
(Nominal)
(Nominal)
PIN
IN
< 15V
O
Open (High)
Open (High)
Open (High)
Open (High)
SHDN PIN
Grounded
Grounded
Grounded
Grounded
U
S
I FOR ATIO
U
Forced to V
Forced to V
OUTPUT/SENSE PINS
W
> 1V
> 1V
≤ 0V
≤ 0V
≤ 0V
≤0V
OUT
OUT
(Nominal)
(Nominal)
U
Reverse Output Current ≈ 15µA (See Figure 3), Input Current ≈ 1µA (See Figure 4)
Reverse Output Current ≈ 15µA (See Figure 3), Input Current ≈ 1µA (See Figure 4)
Reverse Output Current ≈ 15µA Peak (See Figure 3)
Reverse Output Current ≈ 15µA (See Figure 3)
Output Current = 0
Output Current = 0
Output Current = Short-Circuit Current
Output Current = 0
OUTPUT pin of an adjustable device, or the SENSE pin of
a fixed voltage device, is pulled below ground, with the
input open or grounded, current must be limited to less
than 5mA.
In circuits where a backup battery is required, several
different input/output conditions can occur. The output
voltage may be held up while the input is either pulled to
ground, pulled to some intermediate voltage, or is left
open circuit. Current flow back into the output will vary
depending on the conditions. Many battery-powered cir-
cuits incorporate some form of power management. The
following information will help optimize battery life. Table
2 summarizes the following information.
The reverse output current will follow the curve in Figure
3 when the input is pulled to ground. This current flows
through the device to ground. The state of the SHDN pin
will have no effect on output current when the V
pulled to ground.
100
90
80
70
60
50
40
30
20
10
0
0
Figure 3. Reverse Output Current
T
V
(LT1529-3.3/LT1529-5)
V
CURRENT FLOWS
INTO DEVICE
J
OUT
OUT
1
= 25°C, V
LT1529-3.3
= V
= V
2
SENSE
ADJ
OUTPUT VOLTAGE (V)
3
IN
(LT1529)
= 0V
4
5
LT1529
LT1529-5
6
7
8
LT1529 • F03
9
10
IN
152935fb
pin is