MIC5319-2.8YD5 Micrel Inc, MIC5319-2.8YD5 Datasheet
![IC REG LDO 500MA 2.8V TSOT23-5](/photos/7/37/73750/576-tsot-23-5_sml.jpg)
MIC5319-2.8YD5
Specifications of MIC5319-2.8YD5
Available stocks
Related parts for MIC5319-2.8YD5
MIC5319-2.8YD5 Summary of contents
Page 1
... Equipped with a logic-compatible enable pin, the MIC5319 can be put into a zero-off-mode current state, drawing no current when disabled. The MIC5319 is a µCap design operating with very-small ceramic output capacitors for stability, thereby reducing required board space and component cost ...
Page 2
... MIC5319-2.8BML MIC5319-2.9YML MIC5319-3.0YML MIC5319-3.3YML MIC5319-3.3BML MIC5319-5.0YML MIC5319-5.0BML MIC5319YML MIC5319BML MIC5319-1.3HYD5 MIC5319-1.8YD5 MIC5319-1.85YD5 MIC5319-2.5YD5 MIC5319-2.6YD5 MIC5319-2.7YD5 MIC5319-2.8YD5 MIC5319-2.8BD5 MIC5319-2.9YD5 MIC5319-3.0YD5 MIC5319-3.3BD5 MIC5319-3.3YD5 MIC5319-5.0YD5 Notes: 1. Under-bar/Over-bar symbols may not be to scale. 2. For other output voltage options, contact Micrel Marketing. May 2010 Marking (2) Voltage ...
Page 3
... Fixed Adjustable − 5 − Pad HS pad May 2010 MIC5319BML/YML (Adjustable) 6-Pin 2mm × 2mm MLF ® Top View Pin Name Pin Name Fixed Enable Input: Active High. High = ON, Low = OFF. Do not leave 3 EN floating. 2 GND Ground. 1 VIN Supply Input. 5 VOUT Output Voltage. ...
Page 4
... θ (max Exceeding the maximum allowable J(max For outputs below 2.5V, OUT MIC5319 IN Max. Units +1.0 % +2.0 1.2625 V 1.275 %/V 0 400 µA 150 µ µVrms µs 100 0.2 ...
Page 5
... Micrel, Inc. Typical Characteristics May 2010 5 MIC5319 M9999-052510 ...
Page 6
... Micrel, Inc. Typical Characteristics (Continued) May 2010 6 MIC5319 M9999-052510 ...
Page 7
... Micrel, Inc. Functional Characteristics May 2010 7 MIC5319 M9999-052510 ...
Page 8
... Micrel, Inc. Functional Diagram May 2010 MIC5319 Block Diagram − Fixed MIC5319 Block Diagram − Adjustable 8 MIC5319 M9999-052510 ...
Page 9
... Adjustable Regulator Application Adjustable regulators use the ratio of two resistors to multiply the reference voltage to produce the desired output voltage. The MIC5319 can be adjusted from 1.25V to 5.5V by using two external resistors (Figure 1). The resistors set the output voltage based on the following equation: provide ...
Page 10
... JA T (max) = 125°C, the maximum junction temperature of J the die. θ thermal resistance = 93°C/W. JA Table 1 shows junction-to-ambient thermal resistance for the MIC5319 in the 2mm x 2mm MLF θ Recommended JA Package Minimum Footprint ® 2mm × 2mm MLF 93°C/W SOT-23-5 235°C/W Table 1 ...
Page 11
... Micrel, Inc. Package Information May 2010 ® 6-Pin 2mm × 2mm MLF (ML) 11 MIC5319 M9999-052510 ...
Page 12
... Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully May 2010 TSOT-23-5 (D5) indemnify Micrel for any damages resulting from such use or sale. © 2010 Micrel, Incorporated. 12 http://www.micrel.com M9999-052510 MIC5319 nt ...