LP38852SX-ADJ/NOPB National Semiconductor, LP38852SX-ADJ/NOPB Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LP38852SX-ADJ/NOPB
Manufacturer Part Number
LP38852SX-ADJ/NOPB
Description
IC REG LDO 1.5A ADJ FAST TO263-7
Manufacturer
National Semiconductor
Series
PowerWise®r
Datasheet
1.LP38852EVAL.pdf
(18 pages)
Specifications of LP38852SX-ADJ/NOPB
Regulator Topology
Positive Adjustable
Voltage - Output
0.8 ~ 1.8 V
Voltage - Input
0.93 ~ 5.5 V
Voltage - Dropout (typical)
0.13V @ 1.5A
Number Of Regulators
1
Current - Output
1.5A (Max)
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
TO-263-7, D²Pak (7 leads + Tab), TO-263CA
For Use With
LP38852EVAL - BOARD EVALUATION LP38852
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Other names
LP38852SX-ADJ
www.national.com
heat-sink manufacturer datasheet for details and recommen-
dations.
Heat-Sinking The TO-263 Package
The TO-263 package has a θ
rating of 3°C/W. These ratings are for the package only, no
additional heat-sinking, and with no airflow.
The TO-263 package uses the copper plane on the PCB as
a heat-sink. The tab of this package is soldered to the copper
plane for heat sinking. shows a curve for the θ
package for different copper area sizes, using a typical PCB
with 1 ounce copper and no solder mask over the copper area
for heat-sinking.
Figure 3
square inch produces very little improvement. The minimum
value for θ
32°C/W.
Figure 4
TO-263 packages for different ambient temperatures, assum-
FIGURE 3. θ
FIGURE 4. Maximum Power Dissipation vs Ambient
shows the maximum allowable power dissipation for
shows that increasing the copper area beyond 1
Temperature for the TO-263 Package
JA
JA
for the TO-263 package mounted to a PCB is
vs Copper (1 Ounce) Area for the TO-263
package
JA
rating of 60°C/W, and a θ
20213925
JA
20213926
of TO-263
JC
14
ing θ
125°C.
Heat-Sinking The PSOP-8 Package
The LP38852MR package has a θ
a θ
the device DAP soldered to an area of 0.008 square inches
(0.09 in x 0.09 in) of 1 ounce copper, with no airflow.
Increasing the copper area soldered to the DAP to 1 square
inch of 1 ounce copper, using a dog-bone type layout, will
improve the θ
creasing the copper area beyond 1 square inch produces very
little improvement.
Figure 6
the PSOP-8 package for a range of ambient temperatures,
assuming that θ
perature is 125°C.
FIGURE 5. θ
FIGURE 6. Maximum Power Dissipation vs Ambient
JC
JA
rating of 11°C/W. The θ
is 35°C/W and the maximum junction temperature is
shows the maximum allowable power dissipation for
Temperature for the PSOP-8 Package
JA
JA
vs Copper (1 Ounce) Area for the PSOP-8
JA
rating to 98°C/W.
is 98°C/W and the maximum junction tem-
Package
JA
rating of 168°C/W includes
JA
Figure 5
rating of 168°C/W, and
shows that in-
20213927
20213928