MC33269DTRK-5.0G ON Semiconductor, MC33269DTRK-5.0G Datasheet - Page 6
![IC REG LDO 0.8A 5V DPAK](/photos/5/30/53089/dpak_369c_sml.jpg)
MC33269DTRK-5.0G
Manufacturer Part Number
MC33269DTRK-5.0G
Description
IC REG LDO 0.8A 5V DPAK
Manufacturer
ON Semiconductor
Datasheet
1.MC33269TG.pdf
(13 pages)
Specifications of MC33269DTRK-5.0G
Regulator Topology
Positive Fixed
Voltage - Output
5V
Voltage - Input
Up to 20V
Voltage - Dropout (typical)
1.1V @ 800mA
Number Of Regulators
1
Current - Output
800mA
Current - Limit (min)
800mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
TO-252-2, DPak (2 Leads + Tab), TO-252AA, SC-63
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
MC33269DTRK-5.0GOS
MC33269DTRK-5.0GOS
MC33269DTRK-5.0GOSTR
MC33269DTRK-5.0GOS
MC33269DTRK-5.0GOSTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MC33269DTRK-5.0G
Manufacturer:
ON
Quantity:
20 000
Part Number:
MC33269DTRK-5.0G
Manufacturer:
ON/安森美
Quantity:
20 000
output current capability of the regulator is in excess of
800 mA, with a typical dropout voltage of less than 1.0 V.
Internal protective features include current and thermal
limiting.
stability. The capacitor should be at least 10 mF with an
equivalent series resistance (ESR) of less than 10 W but
greater than 0.2 W over the anticipated operating
temperature range. With economical electrolytic capacitors,
cold temperature operation can pose a problem. As
temperature decreases, the capacitance also decreases and
the ESR increases, which could cause the circuit to oscillate.
Also capacitance and ESR of a solid tantalum capacitor is
more stable over temperature. The use of a low ESR ceramic
capacitor placed within close proximity to the output of the
device could cause instability.
transient response or if the regulator is connected to the
Figures 11 through 15 are typical application circuits. The
* The MC33269 requires an external output capacitor for
** An input bypass capacitor is recommended to improve
An input capacitor is not necessary for stability, however
it will improve the overall performance.
The Schottky diode in series with the ground leg of the upper
regulator shifts its output voltage higher by the forward
voltage drop of the diode. This will cause the lower device
to remain off until the input voltage is removed.
Figure 14. Battery Backed−Up Power Supply
Figure 11. Typical Fixed Output Application
**
V
V
**
in
C
in
in
V
C
in
Figure 13. Current Regulator
in
**
**
C
C
in
in
MC33269
MC33269-XX
I out +
Adj
MC33269-XX
MC33269-XX
1.25
R
GND
S
GND
GND
R
S
C
10 mF
V
o
out
*
APPLICATIONS INFORMATION
V
I
C
10 mF
out
C
10 mF
out
o
o
*
*
http://onsemi.com
6
supply input filter with long wire lengths. This will reduce
the circuit’s sensitivity to the input line impedance at high
frequencies. A 0.33 mF or larger tantalum, mylar, ceramic,
or other capacitor having low internal impedance at high
frequencies should be chosen. The bypass capacitor should
be mounted with shortest possible lead or track length
directly across the regulator’s input terminals. Applications
should be tested over all operating conditions to insure
stability.
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated, typically at
170°C, the output is disabled. There is no hysteresis built
into the thermal limiting circuit. As a result, if the device is
overheating, the output will appear to be oscillating. This
feature is provided to prevent catastrophic failures from
accidental device overheating. It is not intended to be used
as a substitute for proper heat−sinking.
***C
The MC34269 develops a 1.25 V reference voltage between the
output and the adjust terminal. Resistor R1, operates with
constant current to flow through it and resistor R2. This current
should be set such that the Adjust Pin current causes negligible
drop across resistor R2. The total current with minimum load
should be greater than 8.0 mA.
Figure 12. Typical Adjustable Output Application
Internal thermal limiting circuitry is provided to protect
R
reduces the output voltage when turned on.
Figure 15. Digitally Controlled Voltage Regulator
2
Adj
sets the maximum output voltage. Each transistor
is optional, however it will improve the ripple rejection.
**
V
**
C
in
V
in
C
in
in
V out + 1.25 1 ) R2
C
MC33269
Adj
Adj
MC33269
Adj
***
R1
) I
R1
R2
R1
R2
Adj
R2
C
10 mF
V
out
o
V
*
C
10 mF
out
o
*