MIC29301-5.0BT Micrel Inc, MIC29301-5.0BT Datasheet - Page 18
![IC REG LDO 3.0A 5.0V TO-220-5](/photos/7/40/74015/576-to-220-5_sml.jpg)
MIC29301-5.0BT
Manufacturer Part Number
MIC29301-5.0BT
Description
IC REG LDO 3.0A 5.0V TO-220-5
Manufacturer
Micrel Inc
Datasheet
1.MIC29152WU_TR.pdf
(23 pages)
Specifications of MIC29301-5.0BT
Regulator Topology
Positive Fixed
Voltage - Output
5V
Voltage - Input
Up to 26V
Voltage - Dropout (typical)
0.37V @ 3A
Number Of Regulators
1
Current - Output
3A
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-220-5 (Straight Leads)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Current - Limit (min)
-
Capacitor Requirements
For stability and minimum output noise, a capacitor on
the regulator output is necessary. The value of this
capacitor is dependent upon the output current; lower
currents
MIC29150/29300/29500/29750 regulators are stable
with the following minimum capacitor values at full load:
Device
MIC29150...............................................10µF
MIC29300...............................................10µF
MIC29500...............................................10µF
MIC29750...............................................22µF
This capacitor need not be an expensive low ESR type:
aluminum electrolytics are adequate. In fact, extremely
low ESR capacitors may contribute to instability.
Tantalum capacitors are recommended for systems
where fast load transient response is important.
Where the regulator is powered from a source with a
high AC impedance, a 0.1µF capacitor connected
between Input and GND is recommended. This capacitor
should have good characteristics to above 250kHz.
Minimum Load Current
The MIC29150–29750 regulators are specified between
finite loads. If the output current is too small, leakage
currents dominate and the output voltage rises. The
following minimum load current swamps any expected
leakage current across the operating temperature range:
Device
MIC29150................................................5mA
MIC29300................................................7mA
MIC29500..............................................10mA
MIC29750..............................................10mA
Micrel, Inc.
May 2010
allow
smaller
Full Load Capacitor
Minimum Load
capacitors.
The
18
Adjustable Regulator Design
The adjustable regulator versions, MIC29xx2 and
MIC29xx3, allow programming the output voltage
anywhere between 1.25V and the 25V. Two resistors are
used. The resistor values are calculated by:
where V
component definition. Applications with widely varying
load currents may scale the resistors to draw the
minimum load current required for proper operation (see
“Minimum Load Current” section).
Error Flag
MIC29xx1 and MIC29xx3 versions feature an Error Flag,
which looks at the output voltage and signals an error
condition when this voltage drops 5% below its expected
value. The error flag is an open-collector output that
pulls low under fault conditions. It may sink 10mA. Low
output voltage signifies a number of possible problems,
including an overcurrent fault (the device is in current
limit) and low input voltage. The flag output is inoperative
during overtemperature shutdown conditions.
Enable Input
MIC29xx1 and MIC29xx2 versions feature an enable
(EN) input that allows ON/OFF control of the device.
Special design allows “zero” current drain when the
device is disabled—only microamperes of leakage
current flows. The EN input has TTL/CMOS compatible
thresholds for simple interfacing with logic, or may be
directly tied to ≤30V. Enabling the regulator requires
approximately 20µA of current.
Figure 4. Adjustable Regulator with Resistors
R
OUT
V IN
1
10µF
=
is the desired output voltage. Figure 4 shows
R
2
×
⎛
⎜ ⎜
⎝
1.240
MIC29152BT
V
OUT
R2
R1
MIC29150/29300/29500/29750
−
1
⎞
⎟ ⎟
⎠
22µF
M9999-050510-B
V OUT