B72590D0050H160 EPCOS Inc, B72590D0050H160 Datasheet

Page 1

CeraDiodes High-speed series Series/Type: Date: November 2010 © EPCOS AG 2010. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. ...

Page 2

CeraDiodes High-speed series Features Very low capacitance values 0 ESD protection to IEC 61000-4-2, level 4 Bidirectional ESD protection in one component No change in ESD protection performance at temperatures (temperature derating) ...

Page 3

... Array, 4-fold, 0508, no semiconductor diode equivalent CDA4C16GTH B72714D0160H060 16 Array, 4-fold, 0612, no semiconductor diode equivalent CDA5C16GTH B72724D0160H062 16 Single, 0201, no semiconductor diode equivalent CDS1C05GTH B72440D0050H060 Single, 0402, SOD-723 CDS2C05HDMI1 B72590D0050H160 CDS2C05HDMI2 B72590D0050H260 CDS2C15GTH B72590D0150H060 15 CDS2C16GTH B72590D0160H060 16 CDS2C20GTH B72590D0200H060 20 Single, 0603, SOD-523 CDS3C05HDMI1 B72500D0050H160 ...

Page 4

CeraDiodes High-speed series Dimensional drawings Single device Array devices 4-fold array Dimension in mm Case size (inch) 0506 (mm) 1216 Min. l 1. 0 Please read Cautions and warnings and Important ...

Page 5

CeraDiodes High-speed series Recommended solder pads Single device Array devices 4-fold array Dimensions in mm Case size (inch) 0506 (mm) 1216 A 0.36 B 0.84 C 0.62 E 0.50 Please read Cautions and warnings and Important notes at the end ...

Page 6

CeraDiodes High-speed series Pin configurations Single device Pin P1 P2 Array devices 4-fold array Pin 2/4 data + 1 supply Pin Please read Cautions and warnings ...

Page 7

CeraDiodes High-speed series Termination Single device Array device Please read Cautions and warnings and Important notes at the end of this document. Page ...

Page 8

... CDS2C05HDMI2 10000 CDS2C15GTH 10000 CDS2C16GTH 10000 CDS2C20GTH 3000 CDA3C05GTH 4000 CDA4C16GTH 4000 CDS3C05HDMI1 4000 CDS3C16GTH 4000 CDS3C30GTH 3000 CDA5C16GTH 4000 CDS4C16GTH 2000 CDA6C05GTH Page Ordering code B72440D0050H060 B72590D0050H160 B72590D0050H260 B72590D0150H060 B72590D0160H060 B72590D0200H060 B72755D0050H062 B72714D0160H060 B72500D0050H160 B72500D0160H060 B72500D0300H060 B72724D0160H062 B72570D0160H060 B72735D0050H062 ...

Page 9

CeraDiodes High-speed series 1 Taping and packing for chip and array CeraDiodes 1.1 Cardboard tape (taping to IEC 60286-3) Dimensions in mm Case size (inch) (mm) Compartment width Compartment length Sprocket hole diameter Sprocket hole pitch Distance center hole to ...

Page 10

CeraDiodes High-speed series 1.2 Blister tape (taping to IEC 60286-3) Dimensions in mm Case size (inch) (mm) Compartment width Compartment length Compartment height Sprocket hole diameter Compartment hole diameter Sprocket hole pitch Distance center hole to center compartment Pitch of ...

Page 11

CeraDiodes High-speed series 1.3 Reel packing Dimensions in mm Reel diameter A Reel width (inside Reel width (outside Package: 8-mm tape Reel material: Plastic 1.4 Packing units Case size 180-mm reel (inch) / (mm) pieces 0201 ...

Page 12

CeraDiodes High-speed series Soldering directions 1 Reflow soldering temperature profile Recommended temperature characteristic for reflow soldering following JEDEC J-STD-020D Profile feature Preheat and soak - Temperature min - Temperature max - Time Average ramp-up rate Liquidous temperature Time at liquidous ...

Page 13

CeraDiodes High-speed series 2 Soldering guidelines The use of mild, non-activated fluxes for soldering is recommended, as well as proper cleaning of the PCB. The components are suitable for reflow soldering to JEDEC J-STD-020D. 3 Solder joint profiles / solder ...

Page 14

CeraDiodes High-speed series 3.3.1 Solder joint profiles for nickel barrier termination Good and poor solder joints caused by amount of solder in infrared reflow soldering Please read Cautions and warnings and Important notes at the end of this document. Page ...

Page 15

CeraDiodes High-speed series 4 Solderability tests Test Standard Test conditions / Sn-Pb soldering Wettability IEC Immersion in 60068-2-58 60/40 SnPb solder using non-activated flux at 215 3 C for 3 0.3 s Leaching IEC Immersion in resistance 60068-2-58 60/40 SnPb ...

Page 16

CeraDiodes High-speed series 5 Notes for proper soldering 5.1 Preheating and cooling The average ramp-up rate must not exceed 3 C/s. The cooling rate must not exceed 8 C/s. 5.2 Repair / rework Manual soldering with a soldering iron must ...

Page 17

CeraDiodes High-speed series 5.7 Placement of components on circuit board advantage to place the components on the board before soldering so that their two termi- nals do not enter the solder oven at different times. Ideally, both ...

Page 18

CeraDiodes High-speed series Symbols and terms CeraDiode Semiconductor diode C max C typ leak ...

Page 19

CeraDiodes High-speed series Cautions and warnings General Some parts of this publication contain statements about the suitability of our CeraDiodes for cer- tain areas of application, including recommendations about incorporation/design-in of these prod- ucts into customer applications. The statements are ...

Page 20

CeraDiodes High-speed series Storage Only store CeraDiodes in their original packaging. Do not open the package before storage. Storage conditions in original packaging: temperature -25 to +45 C, relative humidity 75% an- nual average, maximum 95%, dew precipitation is inadmissible. ...

Page 21

CeraDiodes High-speed series Operation Use CeraDiodes only within the specified operating temperature range. Use CeraDiodes only within specified voltage and current ranges. Environmental conditions must not harm a CeraDiode. Only use them in normal atmospheric conditions. Reducing the atmosphere (e.g. ...

Page 22

Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical ...