2300 Switchcraft Inc., 2300 Datasheet - Page 69
![CONN JACK BLOCK DUAL W/O JACKS](/photos/38/64/386427/2300_sml.jpg)
2300
Manufacturer Part Number
2300
Description
CONN JACK BLOCK DUAL W/O JACKS
Manufacturer
Switchcraft Inc.
Series
2300r
Type
Telephone Jack Panelr
Datasheet
1.2300.pdf
(333 pages)
Specifications of 2300
Rohs Information
Switchcraft RoHS Info.
Connector Type
1/4" Phone Jack (Not Provided)
Number Of Positions
2
Number Of Rows
1
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Termination Style
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
2300
Manufacturer:
NA
Quantity:
20 000
Part Number:
2300-00A8C 3A
Manufacturer:
JXND
Quantity:
20 000
Part Number:
2300-00A8C. 5.8A
Manufacturer:
JXND
Quantity:
20 000
Company:
Part Number:
2300-120PA
Manufacturer:
honeywell
Quantity:
200
Company:
Part Number:
2300-250PA
Manufacturer:
honeywell
Quantity:
200
Part Number:
2300-C009T 3A
Manufacturer:
JXND
Quantity:
20 000
Part Number:
2300-C009T. 5.8A
Manufacturer:
JXND
Quantity:
20 000
Company:
Part Number:
230016003
Manufacturer:
WE
Quantity:
12 000
Company:
Part Number:
230017003
Manufacturer:
HLDY
Quantity:
12 000
Company:
Part Number:
230057GB
Manufacturer:
BUJEON
Quantity:
882
64
w w w . s w i t c h c r a f t . c o m
CONNECTORS & RECEPTACLES
SLIM-LINE CONNECTORS
SLIM-LINE CONNECTORS
SL18 RECEPTACLES
Front of Panel Mount
SL MALE RECEPTACLES
SL FEMALE RECEPTACLES
SLIM-LINE CONNECTORS (continued)
Front of panel mount; 2 through 5 pins (male) or 2 through
5 contacts (female). Also 2-, 3- and 4-contact insert with
3 shunted (N.C.) contacts. Mounting locknut (Part Number
SL01), lockwasher (Part Number SL02), and flat washer
(Part Number SL03) supplied.
Part Number
Part Number
SL182M
SL183M
SL184M
SL185M
SL182F
SL183F
SL184F
SL185F
(17.7)
.696
Contacts
PANEL HOLE
Pins
2
3
4
5
2
3
4
5
Arrangements
SL183FS (typical)
Arrangements
DIMENSIONS ARE FOR REFERENCE ONLY
Contact
Pin
1
2
3
4
A
B
C
D
INSTALLING CABLE CLAMP ON INSERT
To install cable clamp on any insert:
1. Position insert approximately as shown in the diagram.
2. Hold clamp at approximately 30° angle (as shown). Place
3. Press center finger forward into slot and reduce angle of
Cable Clamp SL04
tip of clamp center finger into slot under molded ring “A”.
Note position of notch on insert in relation to slot.
clamp until clamp shoulders seat just ahead of molded
barrier on rear of insert “B”.
MOLDED
RING
“A”
INSERT
NOTCH
ON
(mm)
Note: Contact your Switchcraft Representative for price and delivery
Inch
PHONE: 773 792 - 2700
® Registered trademark of Switchcraft, Inc.
INSERT
“B”
CABLE
CLAMP