RG1005P-1180-P-T1 Susumu, RG1005P-1180-P-T1 Datasheet - Page 15
![RES 118 OHM 1/16W .02% 0402](/photos/12/86/128634/rg1005p_series_sml.jpg)
RG1005P-1180-P-T1
Manufacturer Part Number
RG1005P-1180-P-T1
Description
RES 118 OHM 1/16W .02% 0402
Manufacturer
Susumu
Series
RGr
Datasheet
1.RG1005P-103-D-T10.pdf
(16 pages)
Specifications of RG1005P-1180-P-T1
Resistance (ohms)
118
Power (watts)
0.063W, 1/16W
Composition
Thin Film
Temperature Coefficient
±25ppm/°C
Tolerance
±0.02%
Size / Dimension
0.039" L x 0.020" W (1.00mm x 0.50mm)
Height
0.014" (0.35mm)
Lead Style
Surface Mount (SMD - SMT)
Package / Case
0402 (1005 Metric)
Resistance In Ohms
118
Case
0402 (1005 metric)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Please refer to the following table of the standard E-Series application for resistors.
Preferred value of resistance shall be composed by significant figures shown in the above table and multipliers
including x10Ω, x100Ω, x1,000Ω, x10,000Ω, and x100,000Ω.
¤
¤
¤
Caution for mounting the product
(1) Please be careful not to scratch the protection coating while (pre/after)
(2) When soldering by soldering iron, heating should be done on a land
(3) Remaining flux may lead to deterioration of durability against moisture
(4) Adherence and remaining of ionized impurity also may lead to
(5) High temperature and long soldering may cause the poor soldering
(6) In case of placing resistors in resin after mounting, please pay
E - 6
E - 12
E - 24
E - 96
Caution for mounting the product
specifications in this catalogue are subject to change for future improvement without prior notice
the contents of this catalogue are current as of June 2005
The Susumu World Group companies, including Susumu Company Ltd., Thin Film Technology Corporation,Yokohama Denshi
SERIES
Seiko Company, Ltd., and Cyntec Company Ltd., do not recommend the use of their products in any life support applications
where failure or malfunction of the product can or may cause failure of a life support device or system, or effect in any manner
its safety or effectiveness. Should the customer use a product in a life support application then, in that event, the Susumu
World Group companies disclaim any and all express or implied warranties as to fitness for any particular purpose or as to
merchantability.
mounting. Any scratches may lead to the deterioration on durability
against moisture.
so that the tip of soldering iron will not touch the component itself.
Also, if soldering is done at high temperature, please do soldering
as short time as possible (less than 3 seconds under 350 C is
preferable).
due to corrosion and occurrence of electrolyte. Specially, if high
activating flux, such as chlorine related one, is used, please check its
characteristics before using it.
deterioration of durability against moisture due to corrosion and
occurrence of electrolyte. Please be careful of not to touch the
components with sweated bare hand pre/after mounting.
on electrode.
special attention to the selection for it. It is recommended to check
durability against heat and moisture, good shock absorption, and
not-containing ionized impurity.
1.00
1.00
1.00
4.30
1.00
1.43
2.05
2.94
4.22
6.04
8.66
SUSUMU WORLD GROUP
1.20
1.10
4.70
1.02
1.47
2.10
3.01
4.32
6.19
8.87
1.50
1.50
1.20
5.10
1.05
1.50
2.15
3.09
4.42
6.34
9.09
1.80
1.30
5.60
1.07
1.54
2.21
3.16
4.53
6.49
9.31
STANDARD RESISTANCE VALUES
2.20
2.20
1.50
6.20
1.10
1.58
2.26
3.24
4.64
6.65
9.53
2.70
1.60
6.80
1.13
1.62
2.32
3.32
4.75
6.81
9.76
SIGNIFICANT FIGURES
3.30
3.30
1.80
7.50
1.15
1.65
2.37
3.40
4.87
6.98
(1) Usage and conditions under special environment, it is recommended to
(2) When using the product under high temperature and high humidity
(3) Dissipation, Pulse loading
3.90
2.00
8.20
1.18
1.69
2.43
3.48
4.99
7.15
Environment and conditions of usage
Copyright © 2006 by SUSUMU CO.,LTD.
Published by Overseas Sales,14 Umamawashi-cho,
Kamitoba,Minami-ku,Kyoto 601-8177,Japan
All rights reserved.
This book, or parts there of, may not be reproduced
in any form without permission.
Printed in Japan.
Please use the product under rated power. Also please set the
confirm the specification and reliability of products. Below conditions
are considered as special environments.
maximum voltage under rated voltage upon pulse loading.
1
1
2
3
4
2
Places where products are immersed in such liquids as water,
Direct sunlight, exposure at outdoor, and dusty environment.
A place where condensation is expected.
A place where the exposure to toxic gas (sea breeze, HCl, Cl
When using the product under high temperature environment,
When conducting in high moisture environment or the state of
salt water, oil, acid, and an organic solvent. Or, there is
possibility of splash of these liquids.
SO
including generation of heat under consideration, please
derate the maximum load in accordance with the derating
curve stated on the specification.
condensation, it may lead to the increase in resistance value
or break.
4.70
4.70
2.20
9.10
1.21
1.74
2.49
3.57
5.11
7.32
2
, H
2
S, N
5.60
2.40
1.24
1.78
2.55
3.65
5.23
7.50
4
H
3
, NOx, etc.) is expected.
6.80
6.80
2.70
1.27
1.82
2.61
3.74
5.36
7.68
8.20
3.00
1.30
1.87
2.67
3.83
5.49
7.87
3.30
1.33
1.91
2.74
3.92
5.62
8.06
3.60
1.37
1.96
2.80
4.02
5.76
8.25
3.90
1.40
2.00
2.87
4.12
5.90
8.45
2
,
15