NKN5WSFR-73-0R1 Yageo, NKN5WSFR-73-0R1 Datasheet - Page 6
![RES NON-INDUCT WW 0.1 OHM 5W 1%](/photos/13/82/138250/nkn100jr-52-0r1_sml.jpg)
NKN5WSFR-73-0R1
Manufacturer Part Number
NKN5WSFR-73-0R1
Description
RES NON-INDUCT WW 0.1 OHM 5W 1%
Manufacturer
Yageo
Series
NKNr
Datasheet
1.NKN-50JR-52-0R1.pdf
(11 pages)
Specifications of NKN5WSFR-73-0R1
Resistance (ohms)
0.1
Power (watts)
5W
Composition
Wirewound
Features
Flame Proof, Non-Inductive
Temperature Coefficient
±300ppm/°C
Tolerance
±1%
Size / Dimension
0.256" Dia x 0.689" L (6.50mm x 17.50mm)
Lead Style
Through Hole
Package / Case
Axial
Resistance In Ohms
0.10
Case
Axial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Height
-
(3) Temperature Coefficient Test
(4) Insulation Resistance
(5) Solderability
(6) Resistance to Solvent
(7) Terminal Strength
(8) Load Life in Humidity
(9) Load Life Test
Test of resistors above room temperature 100°C ± 2°C ( Testing Temperature 115°C to 130°C ) at the
constant temperature silicon plate for over 5 minutes. Then measure the resistance value.
The Temperature Coefficient is calculated by the following equation and its value should be within the
range of requested.
Apply test terminal on lead and resistor body.
The test resistance should be high than 100M ohm.
Immerse the specimen into the solder pot at 260 ± 5 °C for 5 ± 0.5 seconds.
At least 95% solder coverage on the termination.
The specimen into the appropriate solvent of IPA condition of ultrasonic machine for 1 minutes.
The specimen is no deterioration of coatings and color code.
Direct Load – Resistors shall be held by one terminal and the load shall be gradually applied in the
direction of the longitudinal axis of the resistor unit the applied load reached 5 pounds。
The load shall be held for 10 seconds. The load of weight shall be ≧ 2.5 kg ( 24.5N ).
Place the specimen in a test chamber at 40 ± 2 °C and 90 ~ 95 % relative humidity. Apply the rated
voltage to the specimen at the 1.5 hours on and 0.5 hour off cycle. The total length of test is 1,000 hours
The change of the resistance value shall be within ± 5 % + 0.05 Ω
Placed in the constant temperature chamber of 70 ± 3 °C the resistor shall be connected to the lead wire
at the point of 25mm. Length with each terminal, the resistors shall be arranged not much effected
mutually by the temperature of the resistors and the excessive ventilation shall not be performed, for 90
minutes on and 30 minutes off under this condition the rated D.C. voltage is applied continuously for
1000+48/-0 hours then left at no-load for 1hour, measured at this time the resistance value。
The change of the resistance value shall be within ± 5 % + 0.05 Ω.
There shall be no remarkable change in the appearance and the color code shall be legible after the test.
Re
sistor
R = Resistance value under the testing temperature
R
t
t
o
0
= Resistance value at the room temperature
= The testing temperature
= Room temperature
Temperatur
e
Coefficien
Page-6
t
=
R
R
−
R
0
0
×
t
−
1
t
0
×
10
6