DSP56311VF150 Freescale Semiconductor, DSP56311VF150 Datasheet - Page 23

• Manufacturer Part Number: DSP56311VF150
• Description: IC DSP 24BIT 150MHZ 196-BGA
• Manufacturer: Freescale Semiconductor
• Series: DSP563xxr
• Type: Fixed Pointr

Specifications of DSP56311VF150

• Interface: Host Interface, SSI, SCI
• Clock Rate: 150MHz
• Non-volatile Memory: ROM (576 B)
• On-chip Ram: 384kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.80V
• Operating Temperature: -40°C ~ 100°C
• Mounting Type: Surface Mount
• Package / Case: 196-MAPBGA
• Device Core Size: 24b
• Format: Fixed Point
• Clock Freq (max): 150MHz
• Mips: 150
• Device Input Clock Speed: 150MHz
• Ram Size: 384KB
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (min): 1.7/1.7/3/3/3/3/3/3V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 196
• Package Type: MA-BGA
• Package: 196MA-BGA
• Numeric And Arithmetic Format: Fixed-Point
• Maximum Speed: 150 MHz
• Device Million Instructions Per Second: 150 MIPS
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

2.3 DC Electrical Characteristics
Freescale Semiconductor
Supply voltage:
•
•
Input high voltage
•
•
•
Input low voltage
•
•
•
Input leakage current
High impedance (off-state) input current
(@ 2.4 V / 0.4 V)
Output high voltage
•
•
Output low voltage
•
•
Internal supply current
•
•
•
PLL supply current
Input capacitance
Notes:
Core (V
I/O (V
D[0–23], BG, BB, TA
MOD/IRQ
JTAG/ESSI/SCI/Timer/HI08 pins
EXTAL
D[0–23], BG, BB, TA, MOD/IRQ
All JTAG/ESSI/SCI/Timer/HI08 pins
EXTAL
TTL (I
CMOS (I
TTL (I
CMOS (I
In Normal mode
In Wait mode
In Stop mode
CCQH
OH
OL
1.
2.
3.
4.
5.
6.
7.
8.
8
8
CCQL
OH
OL
= 3.0 mA, open-drain pins I
= –0.4 mA)
1
, RESET, PINIT/NMI and all
, V
= 10 µA)
Refers to MODA/IRQA, MODB/IRQB, MODC/IRQC, and MODD/IRQD pins.
Section 4.3 provides a formula to compute the estimated current requirements in Normal mode. To obtain these results, all
inputs must be terminated (that is, not allowed to float). Measurements are based on synthetic intensive DSP benchmarks (see
Appendix A ). The power consumption numbers in this specification are 90 percent of the measured results of this benchmark.
This reflects typical DSP applications. Typical internal supply current is measured with V
V
To obtain these results, all inputs must be terminated (that is, not allowed to float). PLL and XTAL signals are disabled during
Stop state.
DC current in Stop mode is evaluated based on measurements. To obtain these results, all inputs not disconnected at Stop
mode must be terminated (that is, not allowed to float).
Periodically sampled and not 100 percent tested.
V
This characteristic does not apply to XTAL and PCAP.
Driving EXTAL to the low V
power consumption, the minimum V
0.9 × V
= –10 µA)
) and PLL (V
3
4
CC
CCQH
CCA
5
= 1.8 V at T
, V
2
= 3.3 V ± 0.3 V, V
CCQH
:
CCD
5,7
5
Characteristics
5
, V
and the maximum V
CCP
CCC
J
)
= 100°C.
, V
1
, RESET, PINIT
CCH
OL
CC
, and V
IHX
= 6.7 mA)
= 1.8 V ± 0.1 V; T
Table 2-3.
or the high V
CCS
ILX
DSP56311 Technical Data, Rev. 8
IHX
)
should be no higher than 0.1 × V
5,7
should be no lower than
ILX
DC Electrical Characteristics
J
= –40°C to +100 °C, C
value may cause additional power consumption (DC current). To minimize
Symbol
I
V
V
I
V
V
V
V
I
CCW
V
I
CCS
C
V
I
CCI
TSI
IHP
IHX
ILP
ILX
IN
OH
OL
IH
IL
IN
L
CCQH
0.8 × V
= 50 pF
V
CC
Min
–0.3
–0.3
–0.3
–10
–10
1.7
3.0
2.0
2.0
2.4
.
—
—
—
—
—
—
—
– 0.01
CCQH
7
CCQP
Typ
150
7. 5
100
1.8
3.3
—
—
—
—
—
—
—
—
—
—
—
—
—
1
DC Electrical Characteristics
= 3.3 V,
0.2 × V
V
V
CCQH
CCQH
V
Max
0.01
CCQH
1.9
3.6
0.8
0.8
0.4
2.5
10
10
10
—
—
—
—
—
+ 0.3
+ 0.3
CCQH
Unit
mA
mA
mA
µA
µA
µA
pF
V
V
V
V
V
V
V
V
V
V
V
V
2-3