PIC18LF2431T-I/SO Microchip Technology, PIC18LF2431T-I/SO Datasheet - Page 3
![IC MCU FLASH 8KX16 28SOIC](/photos/28/69/286927/28-soic_m28b_sml.jpg)
PIC18LF2431T-I/SO
Manufacturer Part Number
PIC18LF2431T-I/SO
Description
IC MCU FLASH 8KX16 28SOIC
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16LF627A-IP.pdf
(8 pages)
3.PIC16F818-ISO.pdf
(6 pages)
4.PIC18F2331-ISO.pdf
(392 pages)
5.PIC18F2331-ISO.pdf
(8 pages)
6.PIC18F2331-ISO.pdf
(6 pages)
7.PIC18F2331-ISO.pdf
(16 pages)
8.PIC18LF2331-ISO.pdf
(4 pages)
9.PIC18LF2331-ISO.pdf
(40 pages)
Specifications of PIC18LF2431T-I/SO
Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LVD, Power Control PWM, QEI, POR, PWM, WDT
Number Of I /o
24
Program Memory Size
16KB (8K x 16)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 5x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SOIC (0.300", 7.50mm Width)
Processor Series
PIC18LF
Core
PIC
Data Bus Width
8 bit
Data Ram Size
768 B
Interface Type
EUSART, I2C, SPI, SSP
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
24
Number Of Timers
1 x 8
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM183021, DV164136
Minimum Operating Temperature
- 40 C
On-chip Adc
5 bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
10. Module: EUSART
11. Module: EUSART
12. Module: EUSART
13. Module: EUSART
© 2005 Microchip Technology Inc.
This module may perform incorrect auto-baud
calculation if the ABDEN (BAUDCTL<0>) bit was
set while the receive pin was at a low level.
Work around
Wait for the RX pin to go high and then set the
ABDEN bit.
In Asynchronous Receiver mode, the EUSART
does not load the SPBRGH value after completion
of auto-baud.
Work around
Do not enable the BRG16 (BAUDCTL<3>) bit.
If the BRG16 is in use, ensure that the auto-baud
SPBRG value does not exceed the 8-bit value.
The CREN (RCSTA<4>) bit is cleared after every
auto-baud operation.
Work around
Upon completion of auto-baud, manually set the
CREN bit.
Writing to the USART/EUSART TXREG register
faster than the baud rate in Synchronous mode
will overwrite the previous value instead of
double-buffering, as in Asynchronous mode.
Work around
Load the first character into TXREG and then wait
for a TX interrupt, or check the TXIF bit before
writing each additional character to TXREG.
PIC18F2331/2431/4331/4431
14. Module: EUSART
15. Module: HSADC
The EUSART cannot receive asynchronous data at
the four fastest baud rates (BRGH = 1, BRG16 = 1
and SPBRG < 4).
Work around
Use a slower baud rate or a faster system clock
speed.
A ΔI
(for V
put into Sleep mode with the HSADC enabled
(ADON = 1) without setting the GO/DONE bit so
that at least one conversion is performed.
Observed ΔI
Work around
If no conversion will be done while in Sleep mode,
disable the HSADC module by clearing the ADON
bit before entering Sleep mode.
If power consumption is an issue for the
application, do not put the part into Sleep mode
with the HSADC enabled if no conversion is to be
performed.
AD
DD
(parameter D026) of greater than 300 μA
= 3V) is observed when the device is
AD
will increase in proportion to V
DS80192C-page 3
DD
.