SP6641AEK-L-5-0 Exar Corporation, SP6641AEK-L-5-0 Datasheet - Page 7

• Manufacturer Part Number: SP6641AEK-L-5-0
• Description: IC DC/DC CONV BOOST 5.0V SOT23-5
• Manufacturer: Exar Corporation
• Type: Step-Up (Boost)r

Specifications of SP6641AEK-L-5-0

• Package / Case: SOT-23-5, SC-74A, SOT-25
• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 5V
• Current - Output: 175mA
• Voltage - Input: 0.5 ~ 4.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Output Voltage: 5 V
• Output Current: 100 mA, 175 mA, 275 mA, 500 mA
• Input Voltage: 2 V, 3.3 V
• Operating Temperature Range: - 40 C to + 85 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -
• Frequency - Switching: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1016-1210

OPERATION
Loop Regulation: continued
The SP6641 feed forward off-time control de-
livers more load current than constant off-time
control because the input battery voltage drops
during its life cycle. The term (I
the average current delivered to the output ca-
pacitor during the discharge phase. This is con-
stant with respect to input and output voltage.
With constant off-time control, the average dis-
charge current term becomes
which decreases as the input voltage drops.
Table 1 illustrates the average inductor current
delivered to the load during discharge versus the
input voltage. The SP6641 feed forward off-
time control and the constant off-time control
are compared. For purposes of illustration, the
off times of each control scheme are normalized
at a typical two cell alkaline input voltage of
2.6V. The values used in Table 1 are:
I
L = 22µH
V
T
T
Table 1- Average I
The following equation defines the burst mode
frequency under heavy load conditions:
where:
V
V
Rev. 5/26/05, *Patent Pending
F
PK
V
3.0
2.6
2.0
1.3
1.0
OFF
OFF
OUT
D
C
BURST
IN
= Average charging switch drop,
= 0.33A
= Forward schottky drop, (0.4V, typ)
= 3.3V
(SP6641) = 1.5V*µs/(3.3-V
(constant) = 2.14µs
Rnmos*I
5.00µs
2.14µs
1.15µs
0.75µs
0.65µs
=
SP6641A
T
(I
(
OFF
V
PK
OUT
-T
K
PK
L
OFF
OFF
vs. Input Voltage
, typically 0.1V
– V
Avg I
*(V
0.30A
0.30A
0.30A
0.30A
0.30A
IN
) (
OUT
SP6641A/6641B 500mA Alkaline DC/DC Boost Regulator in SOT-23
L
-V
V
Constant T
OUT
IN
2.14µs
2.14µs
2.14µs
2.14µs
2.14µs
V
T
PK
)/2L),
OFF
IN
IN
+ V
– K
– V
)
OFF
D
C
–V
Avg I
0.32A
0.30A
0.27A
0.23A
0.22A
/2L) is
C
OFF
)
L
7
Ignoring the conduction losses of V
the burst frequency equation simplifies to:
Startup
The internal regulator circuitry is bootstrapped
to the V
oscillator and charging switch powered from the
V
the reference is established. The reference pro-
vides a REFREADY signal that determines when
output control is handed over to the regulator.
REFREADY shuts down the startup circuit and
enables the regulator when the reference is valid
and V
given control it will continue to pump up the
output at full power until regulation is reached.
For two cell alkaline input voltages and above,
the output voltage will be pulled above +1.9V
quickly through the rectifying diode before the
reference has a chance to establish. In this sce-
nario the startup circuit will coarsely regulate
around +2.8V until the REFREADY signal as-
serts. This keeps the output from overshooting
in startup with higher input voltages.
Startup is guaranteed at +0.9V at room tempera-
ture with a 3kΩ load. Heavier loads will require
a higher input voltage.
Shutdown/Enable Control
Pin 4 of the device is a V
pin that shuts down the converter with the pin
tied to ground, or enables the converter with the
pin tied to V
down the power switch is opened and all circuit
biasing is extinguished leaving only junction leak-
age currents on supply pins 3 and 5. The output
voltage will droop to one diode drop below the
battery voltage through the rectifying diode.
After pin 4 is brought high, the startup circuit is
enabled and starts pumping up the output until
REFREADY hands over control to the internal
regulator.
BATT
F
OUT
BURST
pin to pump up the output voltage until
OUT
is above +1.9V. Once the regulator is
=
BATT
pin. This requires a low voltage
(V
. When the converter is shut-
OUT
K
OFF
– V
© Copyright 2002 Sipex Corporation
V
BATT
IN
OUT
)V
IN
referred control
D
and V
C
,