ZB2430-Q-E-S-U-EVB Laird Technologies, ZB2430-Q-E-S-U-EVB Datasheet - Page 34
![no-image](/images/manufacturer_photos/0/3/378/laird_technologies_sml.jpg)
ZB2430-Q-E-S-U-EVB
Manufacturer Part Number
ZB2430-Q-E-S-U-EVB
Description
KIT BOARD EXTRA ZB2430-Q-E-S-U
Manufacturer
Laird Technologies
Series
ZigBee™ Your Way™ AeroCommr
Type
802.15.4/Zigbeer
Datasheet
1.ZB2430-D-C-S-A-EVB.pdf
(62 pages)
Specifications of ZB2430-Q-E-S-U-EVB
Contents
Board
For Use With/related Products
SDK-ZB2430-Q
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
ZB2430 User’s Manual - v1.6
A T C O M M A N D S
The AT Command mode implemented in the ZB2430 creates a virtual version of the Command/Data pin. The “Enter
AT Command Mode” Command asserts this virtual pin Low (to signify Command Mode) and the “Exit AT Command
Mode” Command asserts this virtual pin High (to signify Data). Once this pin has been asserted Low, all On-the-Fly
CC Commands documented in the manual are supported.
O n - t h e - F l y C o n t r o l C o m m a n d s
The ZB2430 transceiver contains static memory that holds many of the parameters that control the transceiver
operation. Using the “CC” command set allows many of these parameters to be changed during system operation.
Because the memory these commands affect is static, when the transceiver is reset, these parameters will revert back
to the settings stored in the EEPROM.
While in Command mode, the incoming RF interface of the transceiver is active and packets sent from other
transceivers will still be received; however no outgoing RF packets will be sent. The transceiver uses Interface
Timeout/RF Packet Size to determine when a CC Command is complete. Therefore, there should be no delay
between each character as it is sent from the OEM Host to the transceiver or the transceiver will not recognize the
command.
When an invalid command is sent, the radio discards the data and no response is sent to the OEM Host. Table 8
below shows a quick summary of the basic configuration & diagnostic commands available on the ZB2430. For
detailed command information, please refer to the command descriptions immediatly following the Quick Reference
Table.
Enter AT Command Mode
Exit AT Command Mode
Status Request
Read Channel
Write Destination NWK
Address
Read Destination NWK
Address
Auto Destination
Read API Control
Write API Control
Read Digital Input
Read ADC
Write Digital Outputs
Set Power Control
Read NWK Address
Read Parent’s NWK Address
Command Name
<0x41> <0x54> <0x2B> <0x2B> <0x2B> <0x0D>
<0xCC> <0x41> <0x54> <0x4F> <0x0D>
<0xCC> <0x00> <0x00>
<0xCC> <0x02>
<0xCC> <0x10> <0x00> <NWK Hi> <NWK Lo>
<0xCC> <0x11>
<0xCC> <0x15> <Data>
<0xCC> <0x16>
<0xCC> <0x17> <API Control>
<0xCC> <0x20>
<0xCC> <0x21> <Data>
<0xCC> <0x23> <Data>
<0xCC> <0x25> <Power>
<0xCC> <0x8A> <0x00>
<0xCC> <0x8A> <0x01>
T a b l e 8 : C o m m a n d Q u i c k R e f e r e n c e
Command (All bytes in Hex)
www.aerocomm.com
<0xCC> <0x43> <0x4F> <0x4D>
<0xCC> <0x44> <0x41> <0x54>
<0xCC> <Firmware> <Status>
<0xCC> <Channel> <Channel Mask [3-0]>
<0xCC> <0x00> <NWK Hi> <NWK Lo>
<0xCC> <0x00> <NWK Hi> <NWK Lo>
<0xCC> <Data>
<0xCC> <API Control>
<0xCC> <API Control>
<0xCC> <Data>
<0xCC> <ADC Hi> <ADC Lo>
<0xCC> <Data>
<0xCC> <Power>
<0xCC> <0x8A> <NWK Hi> <NWK Lo>
<0xCC> <0x8A> <NWK Hi> <NWK Lo>
Return (All bytes in Hex)
C O N F I G U R I N G T H E Z B 2 4 3 0
2 9