A09-HASM-675 Digi International/Maxstream, A09-HASM-675 Datasheet - Page 32
![no-image](/images/no-image-200.jpg)
A09-HASM-675
Manufacturer Part Number
A09-HASM-675
Description
ANT 900MHZ 6" R/A JOINT W/RPSMA
Manufacturer
Digi International/Maxstream
Series
A09-HASMr
Specifications of A09-HASM-675
Antenna Type
Whip: 1/2 Wave, Right Angle
Number Of Bands
1
Frequency
915MHz (902MHz ~ 928MHz)
Gain
2.1dBi
Termination
RP-SMA
Mounting Type
Connector
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Vswr
-
Height (max)
-
9XTend™ OEM RF Module ‐ Product Manual v2.x4x [2007.01.04]
PK (Maximum RF Packet Size) Command
PL (TX Power Level) Command
PW (Pin Wake-up) Command
<RF Interfacing> The PK command is used to set/
read the maximum size of RF packets transmitted
from an RF module. The maximum packet size
can be used along with the RB and RO parameters
to implicitly set the channel dwell time.
If PK is set above 256 and BR is subsequently
changed to 0, PK will automatically be lowered to
256 and a warning will be raised (refer to the BR
(RF Data Rate) and WN (Warning Data) com-
mands for details).
Changes to the PK parameter may have a second-
ary effect on the RB (Packetization Threshold) parameter. RB must always be less than or equal to
PK. If PK is changed to a value that is less than the current value of RB, the RB value is automati-
cally lowered to be equal to PK.
* When BR = 0 (9600 baud), the maximum PK value is 0x100 (256d). When BR = 1 (115,200
baud), the maximum PK value is 0x800 (2048d).
<RF Interfacing> The PL command is used to set/
read the power level at which the RF module
transmits data.
<Sleep (Low Power)> Under normal operation, an
RF module in Cyclic Sleep Mode cycles from an
active state to a low-power state at regular inter-
vals until data is ready to be received. If the PW
parameter is set to 1, the SLEEP pin (pin 8) can
be used to awaken the module from Cyclic Sleep.
When the SLEEP Pin is de-asserted (low), the
module will be fully operational and will not go
into Cyclic Sleep.
Once the SLEEP pin is asserted, the module will
remain active for the period of time specified by
the ST (Time before Sleep) parameter and will
return to Cyclic Sleep Mode (if no data is ready to
be transmitted). PW Command is only valid if Cyclic Sleep has been enabled.
© 2007 MaxStream, Inc.
AT Command: ATPK
Binary Command: 0x29 (41 decimal)
Parameter Range: 1 - 0x800 [Bytes]
Default Parameter Value:0x100* or 0x800*
(256 or 2048 decimal)
Number of bytes returned: 2
Related Commands: BR (RF Data Rate) RB
(Packetization Threshold), RO (Packetization
Timeout), WN (Warning Data)
AT Command: ATPL
Binary Command: 0x3A (58 decimal)
Parameter Range: 0 - 4
Default Parameter Value: 4
Number of bytes returned: 1
AT Command: ATPW
Binary Command: 0x1D (29 decimal)
Parameter Range: 0 - 1
Default Parameter Value: 0
Number of bytes returned: 1
Related Commands: SM (Sleep Mode), ST
(Time before Sleep)
Parameter
Parameter
Chapter 3 ‐ RF Module Configuration
0
1
2
3
4
0
1
1000 mW (1 Watt)
Configuration
Configuration
Disabled
100 mW
500 mW
Enabled
10 mW
1 mW
32