MDEV-315-HH-CP8-MS Linx Technologies Inc, MDEV-315-HH-CP8-MS Datasheet - Page 3

• Manufacturer Part Number: MDEV-315-HH-CP8-MS
• Description: KIT DEV TX 315MHZ MS SERIES
• Manufacturer: Linx Technologies Inc
• Series: MSr
• Type: Transmitterr

Specifications of MDEV-315-HH-CP8-MS

• Frequency: 315MHz
• Supply Voltage (min): 7 V
• Product: RF Modules
• Maximum Frequency: 315 MHz
• Supply Voltage (max): 16 V
• Supply Current: 500 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: MS Compact Handheld Series - 315MHz
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

SETTING THE TRANSMITTER ADDRESS
OTX-***-HH-CP8-MS BUTTON ASSIGNMENTS
Figure 3: OTX-***-HH-CP8-MS Button Assignments
Page 4
The MS Compact Handheld Transmitter
allows
16,777,216 (2
transmitters are supplied set to the
same address. To avoid contention with
other
relationships, the address can be
changed. This is accomplished by using
a paper clip or probe to press the
CREATE button on the board through
the hole in the back of the case. When
the button is depressed, a LED will light
up in the MODE_IND window, indicating
that the address is being created. The address will be randomized for as long as
the button is held down. When the button is released, the randomized address
is saved and the LED will begin flashing to indicate that the Control Permissions
may now be set. Press the buttons that the transmitter will have the authority to
access. Press the CREATE button with the paper clip again or wait 17 seconds
for it to time out. The address and Control Permissions are now set. The decoder
will need to learn the address before it will accept any transmissions. Please see
the Using the Master Development System section of this data guide or the
Typical Applications section of the MS Series Decoder Data Guide for details.
This diagram illustrates the relationship between the button locations and
encoder data lines.
units
the
24
selection
or
) unique addresses. All
to
create
of
D6
D4
D2
D0
one
unique
of
Figure 2: CREATE Button Access
MODE_IND Window
D7
D5
D3
D1
CREATE Button
THE DECODER BOARD
Figure 4: The Decoder Board RF Area
The Prototyping Area
The Power Supply
The RF Area
The decoder board included with the evaluation kit uses an LR Series receiver
to receive the signal from the Handheld transmitter and then feeds it into an MS
Series decoder. The board is designed to allow full access to the many features
of the decoder and to speed development and integration of the LR and MS into
a product. The following sections describe the features of this board in detail.
The prototyping area on the decoder board contains a large section of plated
through-holes so that external circuitry can be placed on the board. This circuitry
can be interfaced with the MS Series decoder through the breakout header to the
right of the holes. At the bottom of this area is a row connected to the 3V power
supply and at the top is a row connected to ground.
All of the data lines are connected to a wire-wrap header to the right, allowing
easy access from the prototyping area. The Decoder Data and TX ID lines are
also available on the header as well as the PDN line from the RF module. This
allows complete control of the entire system from the prototyping area, giving the
designer a great deal of flexibility in using the board.
The power supply on the decoder board consists of a standard 9V battery and
power jack connected to a 3.0V voltage regulator. It can provide approximately
500mA of current to the prototyping area. If the added circuitry will need more
than this, the designer must add an external supply. If the circuit will consistently
draw more than 100mA of current, it might be better to use the power jack rather
than the battery, as the battery may run down fairly quickly, reducing testing and
development time.
The jack accepts a standard 5.5mm plug with the tip ground and the outer shell
7 to 16VDC positive supply. While a reverse voltage protection diode has been
included on the board to protect the circuitry in case the voltage on the plug is
reversed, it is still a good idea to double-check the polarity.
The figure below shows the RF area of the development board. The board uses
the LR Series receiver as shown. Attach the included antenna to the reverse
polarity SMA connector before operation.
Page 5