RN-220XP Roving Networks Inc, RN-220XP Datasheet

ADAPTER BLUEPORT-XP SRL BATT-PWR

RN-220XP

Manufacturer Part Number
RN-220XP
Description
ADAPTER BLUEPORT-XP SRL BATT-PWR
Manufacturer
Roving Networks Inc
Series
BluePort™-XPr
Datasheets

Specifications of RN-220XP

Function
Transceiver, Bluetooth
Modulation Or Protocol
Bluetooth v2.0, Class 1
Frequency
2.4GHz
Applications
General Purpose
Interface
RS-232
Data Rate - Maximum
232.4kbps
Package / Case
Module
Interface Type
RS-232
Data Rate
232.4 Kbps
Operating Voltage
5 VDC
Antenna
External
Board Size
76.2 mm x 33 mm x 22.9 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Power - Output
-
Sensitivity
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
740-1003
OPERATING MODES
0-Slave Mode - The default mode, whereby other devices can discover and connect to the BluePort.
1 - Master Mode (SM,1<CR>) Enables outbound connections. To connect, use the “C” command.
2-Trigger Mode (SM, 2 <CR>) Automatically connects to stored address, when data is received on local serial port of master.
3-Auto Master Mode (SM,3<CR>) Automatically connects to stored address on power up.
NOTE: In all master modes the device will not be discoverable or remote configurable.
CONFIGURATION SWITCHES ( ALL SWITCHES ARE SET OFF FROM FACTORY )
1- FACTORY DEFAULTS- Set this switch ON, power up the unit, and toggle the switch OFF-ON-OFF
to return the unit to factory settings.
2-AUTO DISCOVER MODE – In Slave mode, will set a special class of device which is used by a remote Blueport Master to auto connect. IF Switch 3 also
SET (auto master), the device performs a search, stores, and connect s to a remote slave which has this switch 2 set .
3- AUTO MASTER MODE- BluePort will act as master, and auto-connect to a stored remote address. You first set the BT address of the device to connect to
using the SR command. Or, have BluePort auto discover and connect by setting this AND Swi t ch 2.
4- DEFAULT BAUDRATE - OFF (factory setting) = 115K, ON = 9600, (overridden if configured).
LEDs
The YELLOW Led shows physical state of the data pins, pulse stretched for eye visibility, and blinks when data is TRANSMITTED or
RECEIVED on the TX and RX pins . The RED Led indicates battery status: If the Led is blinking, battery is low and needs charging. When
charger is connected, RED Led will glow solid, and turn off when charge is complete.
ANT
Connected
MODE
Discoverable/Idle
Boot up, Remote Configurable
Configuring
DEF BR (115K or 9600) - 4
AUTO MASTER
AUTO DISCOVER
FACTORY DEFAULTS - 1
BluePort-XP Install Guide
GREEN LED BLINK
Fast, 10 x per second
2 times per second
1 time per second
On Solid
- 3
- 2
ON- OFF
Version 4.00
DB9

Related parts for RN-220XP

RN-220XP Summary of contents

Page 1

... The YELLOW Led shows physical state of the data pins, pulse stretched for eye visibility, and blinks when data is TRANSMITTED or RECEIVED on the TX and RX pins . The RED Led indicates battery status: If the Led is blinking, battery is low and needs charging. When charger is connected, RED Led will glow solid, and turn off when charge is complete. Version 4.00 ...

Page 2

SERIAL PIN CONFIGURATIONS (you must remove the plastic enclosure to access the jumpers below). NAME DB-9 male IO DIR 1-DCD To 4,6,9 Via R1 2-RX 2-RX INß 3-TX 3-TX OUTà 4-DTR Via R4 5-GND 5-GND <—> ...

Page 3

... Valid commands will return an AOK. commands will return a ?. Type “h”<cr> to see a list of commands, and “d”<cr> to see a summary of current settings. REMOTE VIA BLUETOOTH- Make a connection via Bluetooth, use a terminal emulator, and follow the directions above for local configuration. ...

Page 4

COMMAND SUMMARY ***SET COMMANDS***stored in flash, and only take effect AFTER reboot Example: SU,9600 sets Uart Baudrate to 9600 SN,myname sets Bluetooth name to “myname” SA,1 enables secure authentication SP,secret sets security pincode to “secret” SF,1 restores all values to ...

Page 5

NOTES ON OPERATION: Master Modes: There are 3 different master modes which can be enabled: 1. Manual Mode. In this mode, the Blueport makes connections when a Connect Command “C”, is received. This command can also contain the Bluetooth address ...

Page 6

INSTANT CABLE REPLACEMENT EXAMPLE: MASTER DEF BR (115K or 9600 AUTO MASTER - 3 ANT AUTO DISCOVER - 2 FACTORY DEFAULTS - 1 SLAVE DEF BR (115K or 9600 ANT AUTO MASTER - 3 AUTO DISCOVER ...

Page 7

COMMON PROBLEMS and QUESTIONS: My Bluetooth client can see the Blueport and its serial service, but I can’t connect: This is most likely caused by a security setting on your client pincode is required, the default is “1234”. ...

Page 8

... OTHER PRODUCTS AVAILABLE FROM ROVING NETWORKS RN-1000 Bluetooth Access Point & Print Server RN-700 Bluetooth Terminal Server & Serial/Ethernet Gateway RN-USB Bluetooth Class I (long range) USB Adapter RN-400U Bluetooth USB Printer Adapter RN-800S-AD Bluetooth Sensor AtoD 16bit, 8 channel RN-30S Bluetooth embedded serial module, class I ...

Related keywords