XT09-PKI-E-NA Digi International/Maxstream, XT09-PKI-E-NA Datasheet - Page 21
![no-image](/images/no-image-200.jpg)
XT09-PKI-E-NA
Manufacturer Part Number
XT09-PKI-E-NA
Description
MODEM RF 900MHZ 1W ETHER INT
Manufacturer
Digi International/Maxstream
Series
XTend™r
Datasheet
1.XT09-PKI-E.pdf
(62 pages)
Specifications of XT09-PKI-E-NA
Function
Transceiver, Modem
Modulation Or Protocol
FHSS, FSK
Frequency
900MHz
Interface
RJ-45 Ethernet
Sensitivity
-110dBm
Data Rate - Maximum
10 kbps
Voltage - Supply
7 V ~ 28 V
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Power - Output
-
Applications
-
9XTend‐PKG‐E™ Ethernet RF Modem – Product Manual v2.x4x [2007.01.04]
Note: Do not send com‐
Note: Do not send com‐
mands to the modem
mands to the modem
during flash program‐
during flash program‐
ming (when parameters
ming (when parameters
are being written to the
are being written to the
modem registry).
modem registry).
Wait for the ʺOKʺ sys‐
Wait for the ʺOKʺ sys‐
tem response that fol‐
tem response that fol‐
lows the ATWR
lows the ATWR
command before enter‐
command before enter‐
ing the next command
ing the next command
or use flow control.
or use flow control.
4.1.2. AT Command Examples
4.1.3. Binary Command Example
Terminal Tab (X-CTU Software)
Modem Configuration Tab
A terminal program has been built into the X-CTU software and is located under the 'Terminal' tab.
The Terminal tab provides an easy-to-use interface for programming the modem.
System Response. When a command is sent to the modem, the modem will parse and execute
the command. Upon successful execution of a command, the modem returns an "OK" message. If
execution of a command results in an error, the modem returns an "ERROR" message.
Restore RF Modem Default Parameters (Using the ‘Terminal’ tab of the X-CTU Software)
NOTE: Default parameter values of the RF Modem can also be restored by selecting the ʹRestoreʹ button located
on the “Modem Configuration” tab [refer to the example below].
Sample Configuration: Restore RF Modem Defaults
To Send Binary Commands:
Note: CTS (GPO1) is high when a command is being executed. Hardware flow control must be disabled
as CTS will hold off parameter bytes.
Example: Both of the following examples restore the XTend Modem's factory defaults and save
the parameters to non-volatile memory.
Method 1 (One line per command)
Method 2 (Multiple commands on one line)
Example: Utilize the X-CTU “Modem Configuration” tab to restore default parameter values.
After establishing a connection between the modem and a PC [refer to the 'Setup' section
above], select the “Modem Configuration” tab of the X-CTU Software.
1.
2.
Example: Use binary commands to change the RF modem's destination address to 0x1A0D and
save the new address to non-volatile memory.
1.
2.
3.
4.
© 2007 MaxStream, Inc., Confidential & Proprietary ‐ All Rights Reserved
RT Command must be set to '1' in AT Command Mode to enable binary programming.
Assert CMD (Pin 10 is driven high). (Enter Binary Command Mode)
Send Bytes [parameter bytes must be 2 bytes long]:
De-assert CMD (GPI1 is driven low). (Exit Binary Command Mode)
Select the 'Read' button.
Select the 'Restore' button.
Send AT Command
+++
ATRE <Enter>
ATWR <Enter>
ATCN <Enter>
Send AT Command
+++
ATRE, WR <Enter>
ATCN <Enter>
00
0D
1A
08
(Send DT (Destination Address) Command)
(Least significant byte of parameter bytes)
(Most significant byte of parameter bytes)
(Send WR (Write) Command)
System Response
OK <CR> (Enter into Command Mode)
OK <CR> (Restore RF modem default parameter values)
OK <CR> (Write to non-volatile memory)
OK <CR> (Exit Command Mode)
System Response
OK <CR> (Enter into Command Mode)
OK <CR> (Execute multiple commands)
OK (Exit AT Command Mode)
21