XB24-BCIT-004 Digi International/Maxstream, XB24-BCIT-004 Datasheet - Page 85
![no-image](/images/no-image-200.jpg)
XB24-BCIT-004
Manufacturer Part Number
XB24-BCIT-004
Description
MODULE 802.15.4 SER 2 CHIP ANT
Manufacturer
Digi International/Maxstream
Series
XBee™r
Datasheet
1.XB24-BPDK.pdf
(91 pages)
Specifications of XB24-BCIT-004
Frequency
2.4GHz
Data Rate - Maximum
250kbps
Modulation Or Protocol
802.15.4
Applications
Home/Building Automation, Industrial Control, ZigBee™
Power - Output
2 mW (3 dBm)
Sensitivity
-96dBm
Voltage - Supply
2.1 V ~ 3.6 V
Current - Receiving
38mA
Current - Transmitting
35mA
Data Interface
PCB, Through Hole
Antenna Connector
On-Board, Chip
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
Appendix B: Agency Certifications
United States FCC
OEM Labeling Requirements
FCC Notices
The XBee ZNet 2.5 RF Module complies with Part 15 of the FCC rules and regulations. Compliance
with the labeling requirements, FCC notices and antenna usage guidelines is required.
To fufill FCC Certification, the OEM must comply with the following regulations:
Required FCC Label for OEM products containing the XBee ZNet 2.5 RF Module
Required FCC Label for OEM products containing the XBee PRO ZNet 2.5 RF Module
IMPORTANT: The XBee ZNet 2.5 and XBee PRO ZNet 2.5 RF Module have been certified by the
FCC for use with other products without any further certification (as per FCC section 2.1091).
Modifications not expressly approved by Digi could void the user's authority to operate the
equipment.
IMPORTANT: OEMs must test final product to comply with unintentional radiators (FCC section
15.107 & 15.109) before declaring compliance of their final product to Part 15 of the FCC Rules.
IMPORTANT: The RF module has been certified for remote and base radio applications. If the
module will be used for portable applications, the device must undergo SAR testing.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Re-orient or relocate the receiving
antenna, Increase the separation between the equipment and receiver, Connect equipment and
receiver to outlets on different circuits, or Consult the dealer or an experienced radio/TV
technician for help.
Contains FCC ID: OUR-XBEE2*
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (i.) this device may not cause harmful interference and (ii.) this device must accept any
interference received, including interference that may cause undesired operation.
Contains FCC ID:MCQ-XBEEPRO2*
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (i.) this device may not cause harmful interference and (ii.) this device must accept any
interference received, including interference that may cause undesired operation.
© 2008 Digi International, Inc.
1.The system integrator must ensure that the text on the external label provided with this
device is placed on the outside of the final product. [Figure A-01]
2.XBee ZNet 2.5 RF Module may only be used with antennas that have been tested and
approved for use with this module [refer to the antenna tables in this section].
WARNING: The Original Equipment Manufacturer (OEM) must ensure that FCC labeling
requirements are met. This includes a clearly visible label on the outside of the final
product enclosure that displays the contents shown in the figure below.
84