AC4490-200M Laird Technologies, AC4490-200M Datasheet - Page 21
![TXRX 900MHZ 3.3-5.5V TTL 200MW](/photos/14/19/141948/ac4490-200m_sml.jpg)
AC4490-200M
Manufacturer Part Number
AC4490-200M
Description
TXRX 900MHZ 3.3-5.5V TTL 200MW
Manufacturer
Laird Technologies
Series
AeroCommr
Specifications of AC4490-200M
Frequency
902MHz ~ 928MHz
Data Rate - Maximum
115.2kbps
Modulation Or Protocol
FHSS, FSK
Applications
AMR, Fire & Security Alarms, Telemetry
Power - Output
5mW ~ 200mW
Sensitivity
-110dBm
Voltage - Supply
3.3V, 5V
Current - Transmitting
68mA
Data Interface
Connector, 2 x 10 Header
Antenna Connector
MMCX
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Output Power
200 mW
Antenna
Integral and External Dipole
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Memory Size
-
Current - Receiving
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
AC4490-200M-01
AC4490 User’s Manual
I N T E R F A C E T I M E O U T / R F P A C K E T S I Z E
Interface Timeout (EEPROM address 0x58), in conjunction with RF Packet Size (EEPROM address 0x5B), determines
when a buffer of data will be sent out over the RF as a complete RF packet, based on whichever condition occurs first.
Interface Timeout – Interface Timeout specifies a maximum byte gap between consecutive bytes. When that byte gap
is exceeded, the bytes in the transmit buffer are sent out over the RF as a complete packet. Interface Timeout is
adjustable in 0.5ms increments and has a tolerance of ±0.5ms.
minimum of 2. The default value for Interface Timeout is 0x04 (2ms) and should be adjusted accordingly when
changing the transceiver baud rate.
RF Packet Size – When the number of bytes in the transceiver transmit buffer equals RF Packet Size, those bytes are
sent out as a complete RF packet. It is much more efficient to send a few large packets rather than several short
packets as every packet the transceiver sends over the RF contains extra header bytes which are not included in the
RF Packet Size. RF packet size can be set to a maximum of 0x50 (80 bytes) and must be set to a minimum of 0x06 in
order to send the Enter AT Command mode command. To change the RF packet size from the default value, Auto
Config must be disabled and the appropriate Auto Config parameters must be changed.
Baud Rate
1. 57,600 is the default baud rate
2. 0x00 will yield a stop bit of 421 uS. The stop bit at 1200 baud should actually be 833 uS.
115,200
57,600
38,400
28,800
19,200
14,400
9,600
4800
2400
1200
1
BaudL
(0x42)
0xFE
0xFC
0xFA
0xE8
0xD0
0xA0
T a b l e 7 : B a u d R a t e / I n t e r f a c e T i m e o u t
0xF8
0xF4
0xF0
0x40
BaudH
(0x43)
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
BaudL
www.aerocomm.com
BAUD
=
BaudH
Low 8 bits of BAUD (base 16)
Minium Interface
=
Timeout (0x58)
----------------------------------------------- -
64
=
×
14.7456
DesiredBaud
Always 0
0x02
0x02
0x02
0x02
0x03
0x04
0x05
0x09
0x11
0x21
×10
6
Therefore, the Interface Timeout should be set to a
Stop Bit Delay (0x3F)
0x00
0xFC
0xFF
0x03
0x08
0x0E
0x19
0x23
0x39
0x7A
2
S E R I A L I N T E R F A C E
1 5