ATA5429-PLQW Atmel, ATA5429-PLQW Datasheet - Page 72
![IC TXRX ASK/FSK 915MHZ 48-QFN](/photos/7/34/73471/48-vqfn-6_543-5130_01-4_sml.jpg)
ATA5429-PLQW
Manufacturer Part Number
ATA5429-PLQW
Description
IC TXRX ASK/FSK 915MHZ 48-QFN
Manufacturer
Atmel
Specifications of ATA5429-PLQW
Frequency
915MHz
Data Rate - Maximum
20kbps
Modulation Or Protocol
ASK, FSK
Applications
Alarm, ISM, Telemetry
Power - Output
5dBm
Sensitivity
-112.5dBm
Voltage - Supply
2.4 V ~ 3.6 V or 4.4 V ~ 6.6 V
Current - Receiving
10.5mA
Current - Transmitting
10mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
48-VQFN Exposed Pad, 48-HVQFN, 48-SQFN, 48-DHVQFN
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Product Depth (mm)
7mm
Product Height (mm)
0.9mm
Product Length (mm)
7mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
Lead Free Status / Rohs Status
Compliant
Other names
ATA5429-PLQW
ATA5429-PLQWTR
ATA5429-PLQWTR
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for T
and V
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
72
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
2.18
2.19 RSSI output
2.20
No. Parameters
VS2
Useful signal to interfering
signal ratio
Output resistance RSSI
pin
= V
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50 according to
ATA5423/ATA5425/ATA5428/ATA5429
VAUX
component values according to
with component values according to
= 5.0V (Base
-
station Application). Typical values are given at f
Test Conditions
Peak level of useful
signal to peak level of
interferer for BER < 10
with any modulation
scheme of interferer
FSK BR_Ranges 0, 1, 2
FSK BR_Range_3
ASK (P
Dynamic range
Lower level of range
f
f
f
f
f
Upper level of range
f
f
f
f
f
Gain
Output voltage range
RX mode
TX mode
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
= 315 MHz
= 345 MHz
= 433.92 MHz
= 868.3 MHz
= 915 MHz
= 315 MHz
= 345 MHz
= 433.92 MHz
= 868.3 MHz
= 915 MHz
RF
< P
Table 3-2 on page 12
amb
RFIN_High
Table 3-7 on page
= 25°C, V
)
-3
VS1
(4), 36
(4), 36
(4), 36
(4), 36
(4), 36
Pin
(4)
(4)
(4)
36
= V
(1)
VS2
and RF_OUT matched to 50 according to
22.
= 3.0V (1
SNR
P
SNR
P
Symbol
SNR
OV
RFIN_High
RFIN_Low
D
R
RSSI
RSSI
FSK0-2
RSSI
FSK3
ASK
-
RF
battery application), V
= 433.92 MHz unless otherwise specified. Details
Min.
400
5.5
32
8
–
–
–
–
–
Typ.
–
–
–
–
–
8.0
10
70
10
40
116
115
115
112
111
2
4
46
45
45
42
41
VS2
= 6.0V (2-battery application)
Figure 3-1 on page 11
Figure 3-10 on page 21
Max.
1100
10.5
12.5
12
50
3
6
4841D–WIRE–10/07
mV/dB
Unit
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm
mV
dB
dB
dB
dB
k
Type*
with
B
B
B
A
A
A
A
A
C