ZICM2410P0-1C CEL, ZICM2410P0-1C Datasheet - Page 5
![MODULE MESHCONNECT TXRX W/CONN](/photos/14/20/142068/zicm2410p0-1c-kit1-1_sml.jpg)
ZICM2410P0-1C
Manufacturer Part Number
ZICM2410P0-1C
Description
MODULE MESHCONNECT TXRX W/CONN
Manufacturer
CEL
Series
MeshConnect™r
Specifications of ZICM2410P0-1C
Frequency
2.4GHz
Data Rate - Maximum
1Mbps
Modulation Or Protocol
802.15.4 Zigbee
Applications
Home/Building Automation, Industrial Control
Power - Output
6dBm
Sensitivity
-97dBm
Voltage - Supply
2.1 V ~ 3.3 V
Current - Receiving
35mA
Current - Transmitting
44mA
Data Interface
Pads for Pins
Memory Size
96kB Flash, 8 kB RAM
Antenna Connector
U.FL
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Wireless Frequency
2.4 GHz
Interface Type
I2S, SPI, UART
Security
128 bit AES
Operating Voltage
2.1 V to 3 V
Output Power
5 mW
Antenna
U.FL Connector
Operating Temperature Range
- 40 C to + 85 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
ZIC2410
ANTENNA
CEL's MeshConnect modules include an integrated Printed Circuit Board (PCB) trace antenna. An optional u.FL connector
can be specified, providing connection to a 50-ohm external antenna of the user’s choice. See Ordering Information on
page 1.
The PCB antenna employs an F-Antenna topology that is compact and supports an omni-directional radiation pattern.
To maximize antenna efficiency, an adequate ground plane must be provided on the host PCB. Correctly positioned, the
ground plane on the host PCB (but not directly under the F-Antenna). Correctly positioned, the ground plane on the host
PCB board under the module will contribute significantly to the antenna performance. The position of the module on the
host board and overall design of the product enclosure contribute to antenna perfor mance. Poor design affects radiation
patterns and can result in reflection, diffraction, and/or scattering of the transmitted signal.
Here are some design guidelines to help ensure antenna performance:
For optimum antenna performance, the MeshConnect modules should be mounted with the PCB trace antenna
overhanging the edge of the host board. To further improve performance, a ground plane may be placed on the host board
under the module, up to the antenna. The installation of an uninterrupted ground plane on a layer directly beneath the
module will also allow you to run traces under this layer. CEL can provide assistance with your PCB layout.
MODES OF OPERATION
There are three power down modes in the ZIC2410. Each mode can be set using the PDMODE [1:0] bits in the PDCON
register and power down modes can be started by setting the PDSTART bit to 1. Each mode has a different current
consumption and wake-up sources, please refer to the ZIC2410 datasheet for further information on the available power
down modes. Table 8 describes the three power down modes.
•
•
•
•
•
Never place the ground plane or route copper traces directly underneath the antenna portion of the module.
Never place the antenna close to metallic objects.
In the overall design, ensure that wiring and other components are not placed near the antenna.
Do not place the antenna in a metallic or metalized plastic enclosure.
Keep plastic enclosures 1cm or more from the antenna in any direction.
PDMODE [1:0]
0
1
2
3
Active (Normal Operation)
Description
PM1 mode
PM2 mode
PM3 mode
Table 8 – Power Down Modes
Sleep Timer interrupt,
Sleep Timer interrupt,
Wake-Up Source
External interrupt
External interrupt
External interrupt
Hardware Reset,
Hardware Reset,
Hardware Reset,
-
MeshConnect™ Module
configuration is required)
configuration is required)
(After wake-up, register
(After wake-up, register
Regulator for Digital
block
OFF
OFF
ON
-
Page 5