SI1002-C-GM Silicon Laboratories Inc, SI1002-C-GM Datasheet - Page 81

• Manufacturer Part Number: SI1002-C-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1002-C-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 13dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 30mA
• Data Interface: PCB, Surface Mount
• Memory Size: 64kB Flash, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 13 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4.1 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 64 KB
• Data Ram Size: 4352 B
• Supply Current (max): 4.1 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1878-5

SFR Definition 5.1. ADC0CN: ADC0 Control
SFR Page = 0x0; SFR Address = 0xE8; bit-addressable;
Name
Reset
Type
Bit
2:0
7
6
5
4
3
Bit
ADC0CM[2:0] ADC0 Start of Conversion Mode Select.
BURSTEN
AD0BUSY
AD0WINT
AD0INT
AD0EN
AD0EN
Name
R/W
7
0
BURSTEN
ADC0 Enable.
0: ADC0 Disabled (low-power shutdown).
1: ADC0 Enabled (active and ready for data conversions).
ADC0 Burst Mode Enable.
0: ADC0 Burst Mode Disabled.
1: ADC0 Burst Mode Enabled.
ADC0 Conversion Complete Interrupt Flag.
Set by hardware upon completion of a data conversion (BURSTEN=0), or a burst
of conversions (BURSTEN=1). Can trigger an interrupt. Must be cleared by soft-
ware.
ADC0 Busy.
Writing 1 to this bit initiates an ADC conversion when ADC0CM[2:0] = 000.
ADC0 Window Compare Interrupt Flag.
Set by hardware when the contents of ADC0H:ADC0L fall within the window speci-
fied by ADC0GTH:ADC0GTL and ADC0LTH:ADC0LTL. Can trigger an interrupt.
Must be cleared by software.
Specifies the ADC0 start of conversion source.
000: ADC0 conversion initiated on write of 1 to AD0BUSY.
001: ADC0 conversion initiated on overflow of Timer 0.
010: ADC0 conversion initiated on overflow of Timer 2.
011: ADC0 conversion initiated on overflow of Timer 3.
1xx: ADC0 conversion initiated on rising edge of CNVSTR.
R/W
6
0
AD0INT
R/W
5
0
AD0BUSY AD0WINT
Rev. 1.0
W
4
0
Function
R/W
3
0
Si1000/1/2/3/4/5
2
0
ADC0CM
R/W
1
0
0
0
81