PIXLITE-SO-PLFE Flexipanel, PIXLITE-SO-PLFE Datasheet - Page 7
![MODULE ZIGBEE SW FAST 24-SMD](/photos/14/21/142140/pixlite-so-plfe_sml.jpg)
PIXLITE-SO-PLFE
Manufacturer Part Number
PIXLITE-SO-PLFE
Description
MODULE ZIGBEE SW FAST 24-SMD
Manufacturer
Flexipanel
Series
Pixie™r
Specifications of PIXLITE-SO-PLFE
Frequency
2.4GHz
Modulation Or Protocol
802.15.4 Zigbee
Power - Output
0dBm
Voltage - Supply
2.1 V ~ 3.6 V
Current - Receiving
25mA
Current - Transmitting
25mA
Data Interface
PCB, Surface Mount
Memory Size
32kB ROM, 1536B RAM
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
26-SMD
Wireless Frequency
2.4 GHz
Interface Type
UART, SPI
Modulation
DSSS OQPSK
Security
APS, NWK, MAC, ZDO
Output Power
1 mW
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Applications
-
Sensitivity
-
Data Rate - Maximum
-
For Use With/related Products
PIC18LF4620
Other names
658-1008-5
PIXIE-LITE-SO-PLFE
PIXIE-LITE-SO-PLFE
Regulatory
EMI ratings
The Pixie and Pixie Lite modules integrate the EasyBee
reference design which has been independently tested
for FCC and CE compliance.
FCC compliance requires us to state the following:
1. This device complies with Part 15 of the FCC
2. OEM products incorporating EasyBee must
3.
ZigBee Alliance Membership
FlexiPanel is an Adopter Member of the Zigbee Alliance.
To use the Microchip Stack for ZigBee, either you must
be a member of the Zigbee Alliance. Alternatively we as
alliance members can program your firmware into the
Pixies and sell you pre-programmed ZigBee devices for
commercial use.
OUI number / MAC address
All IEEE 802.15.4 devices such as Pixie must use a
unique 8-byte MAC address. The first 3 bytes (the ‘OUI’
p7
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference
operation.
include an external label containing the
following text legible to the naked eye:
Changes or modifications to the module may
void its certification.
Debug optimizations only should be reserved for
files that require debugging.
Oscillator configuration bits must be set according
to the oscillator mode in use.
Brownout reset is recommended at 2.0V for 4MHz
devices and 2.7V for 16MHz devices.
The watchdog timer should be enabled in
software as required.
devices, the postscaler value should be set
according to the desired wakeup rate (1:256 being
approximately 1 second).
CCP2 Mux should be set to RB3.
PORTB<4:0> should be configured as digital I/O
on reset.
If MCLR is enabled, the OEM must ensure its
correct operation.
provided.
17-Mar-08
Contains Transmitter Module
FCC ID:UGAZBMR10
that
Pixie DS481-17
may
No on-board circuitry is
For battery powered
cause
undesired
© FlexiPanel Ltd
number) are licensed to a company by IEEE for an
annual fee. The licensee is then free to uniquely assign
the remaining 5 bytes.
FlexiPanel Ltd can provide MAC addresses under its
OUI license for the transceivers it manufactures. OEMs
therefore do not need to apply for an OUI number.
FlexiPanel Ltd’s OUI number is 00-15-C8.
For R&D purposes (i.e. in the lab or classroom), the
following MAC addresses may be used:
(Remember that PICs are little-endian, so MAC[7] = 00,
MAC[6] = 15, MAC[2] = C8, etc.) Volume customers
may reserve a contiguous block of MAC addresses.
For commercial purposes, contact FlexiPanel Ltd or
your distributor for an allocation of MAC addresses.
Preloading the MAC Address
All firmware from FlexiPanel Ltd permits the use of
SQTP to automatically set MAC addresses when
programming
programmer. The ROM locations 0x006A to 0x007B
contain the following assembler code:
During initialization, the firmware checks to see whether
the MAC address has been set.
AddrValid is nonzero, it will set the MAC address to
the values given in Macbyte0 to Macbyte7.
firmware ships with AddrValid equal to zero, but it
may be set during programming using SQTP.
SQTP is a feature of the PM3 programmer that allows
you to generate a file of IDs, in this case MAC
addresses,
programming.
addresses:
00:15:C8:38:41:00:00:00 to 00:15:C8:38:41:00:FF:FF
1. In MPLAB, ensure the PM3 programmer is
2. From the Programmer menu, select Settings…
3. Fill in the SQTP tab as shown in the following
Patents may apply and/or pending
selected.
graphic, except insert the start of your personal
MAC allocation in the “Start Value” box, and the
number of sequential MAC addresses to allocate in
the “Number of parts” box. (Note the Start value is
FF, specifying the AddrValid value, followed by
the MAC address, most significant byte first.)
0x006A
0x006C
0x006E
0x0070
0x0072
0x0074
0x0076
0x0078
0x007A
and
using
To set up SQTP to allocate MAC
allocated
RETLW
RETLW
RETLW
RETLW
RETLW
RETLW
RETLW
RETLW
RETLW
Microchip
them
Macbyte0
Macbyte1
Macbyte2
Macbyte3
Macbyte4
Macbyte5
Macbyte6
Macbyte7
AddrValid
Technology’s
If it has not, and
www.FlexiPanel.com
uniquely
during
PM3
The