E3JU-25DM4T-MN1 Omron, E3JU-25DM4T-MN1 Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
E3JU-25DM4T-MN1
Manufacturer Part Number
E3JU-25DM4T-MN1
Description
T-BEAM RCVR RELAY TMR MINI CONN
Manufacturer
Omron
Series
E3JUr
Datasheet
1.E3JU-25L-6.pdf
(12 pages)
Specifications of E3JU-25DM4T-MN1
Sensing Distance
984.252" (25m)
Sensing Method
Through-Beam
Output Configuration
Relay - Dark-ON/Light-ON - Selectable
Mounting Type
Bracket Mount
Voltage - Supply
12 V ~ 240 V
Package / Case
Module, Connector
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Supply
-
Response Time
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
E3JU25DM4TMN1
J BRAD HARRISON MINICHANGE
Note: The above part numbers represent Brad Harrison (Daniel Woodhead) part numbers not Omron part numbers. Please contact your
Precautions
J HIGH-VOLTAGE LINES
Do not place sensor power supply or signal lines within the same
conduit as high-voltage power lines.
J VOLTAGE RATINGS
Do not exceed rated supply voltage, ripple percent (for DC
models), or load current limits.
J AMBIENT LIGHTING
Do not install sensor in direct sunlight, or other sources of strong
ambient light.
J ENVIRONMENTAL CONDITIONS
Do NOT install sensor in areas that have any of these conditions:
#
#
#
E3JU
Connector type
5-pole female connectors
4-pole female connectors
2-pole female connectors
MiniChange Connector Cables
C:/CEDSAX4
Cover Screw Torque:
The torque of the cover screw must not exceed 3.5 kgScm
(3 inSlb). Over-torquing twill cause the plastic parts to crack.
These photoelectric sensors should not be used in personal
safety applications. Using the sensor as a safety device may
cause an unsafe condition that could lead to serious injury or
death.
p
p
p
High humidity, or where condensation would result.
Corrosive gas.
High vibration or shock.
!
!
local Omron distributor for future availability by Omron and other equivalent Connector Cables.
CAUTION
WARNING
R
Applicable sensors
E3JU-jjM4j-MN1
E3JU-jjP4j-MN1
E3JU-25jj-MN1 emitter
3JU jj
3JU jj
3JU 5jj
R
j
j
CONNECTOR CABLES
e
e
J POWER SUPPLY
If a switching power supply is used, or when using with an
inverter or servomotor, ground the FG (frame ground) and
G (ground) terminals on the power supply for proper operation to
avoid damaging the sensor.
J WATER EXPOSURE
Do not use the sensor where it may be immersed, is outdoors, or
exposed to rain.
J PROPER MOUNTING SCREWS
Use M5 screws and washers to mount sensor and bracket.
J MECHANICAL SHOCK
Avoid mechanical shock during installation which may damage
the housing.
J CONNECTOR
#
#
#
#
When connecting or disconnecting the connector, hold the
connector cover to avoid tension on housing.
Tighten connector only by hand. Do not use tools, which may
damage the connector.
Always disconnect power before connecting or disconnecting
the connector.
Be sure that the connector is tightened securely. If this is not
done, the sensor enclosure rating may be reduced, or the
connector may loosen and affect the enclosure rating.
Length
6 foot
12 foot
20 foot
6 foot
12 foot
20 foot
6 foot
12 foot
20 foot
Straight
41307
41308
41322
41108
41109
41177
40711
40712
40748
Right angle
41307-90
41308-90
41322-90
41108-90
41109-90
41177-90
40711-90
40712-90
40748-90
E3JU
11